Jump to content
SAU Community

Iphone/ipod Connector For Sale****

YASIDI
 Share

Recommended Posts

YASIDI Explorer

YASIDI

Posted
Posted

Hey guys,

I have a brand new, never fitted iPhone control unit for the V35. It's on-board software translates commands from your factory radio's CD-Changer into commands the iPod understands. This interface enables the iPod to coexist with your factory system and provides a line-level input to your audio system for optimal sound quality.

It is plug and play, allows you to control the iPhone through the steering wheel controls. There Are 3 modes of controlling your iPod: direct mode, playlist mode, and folder mode.

All iPhone/pod text like song name and artist, album titles and such, is displayed on your standard radio display.

It also charges the iPhone while in use, and there is an auxiliary RCA input for any other dvd players, mp3, whatever.

Bought this for $190 + around $40 shipping around 6 months ago.

Yours for $139, postage included.

AE09B25C-AD75-4C0F-A4B4-A456960C5381-6246-000009686D756180.jpg

B6823B72-15CD-4C5F-8D62-55316B71E2CB-6246-0000096872A2B7C4.jpg

632D8E0E-2263-4999-889A-92BC921872ED-6246-000009687E7050D0.jpg

Link to comment
https://www.sau.com.au/forums/topic/413164-iphoneipod-connector-for-sale/
Share on other sites
YASIDI Explorer

YASIDI

Posted
  • Author
Posted

Hey Guys,

This unit is still up for sale. Sorry for my delayed response I do not check this forum as often as I probably should.

To my knowledge this is not only for cars with a boot mounted CD stacker, it plugs straight into the back of the standard V35 head unit.

Raween I have replied to your private message, hopefully helps to answer your questions.

sonicii Veteran

sonicii

Posted
Posted

Interested in this too, but I saw this on the USA Spec website..

You can use the USA SPEC PA15-NIS model if the vehicle is compatible with the PA15-INFI but DOES NOT have SAT receiver or if it's NOT pre-wired for SAT. PA15-NIS's functionality is 100% equivalent to the PA15-INFI. PA15-NIS connects to the radio where as the PA15-INFI connects to the SAT receiver.

Just a bit worried as this unit is the PA15-INFI

YASIDI Explorer

YASIDI

Posted
  • Author
Posted (edited)

Before I bought this, I spoke to the company and this is the model that was recommended to me for my car.

I never installed it though so I can't say I'm 110% certain, however, I would be pretty surprised if it's not the right one.

If you want to buy it and give it a go, I'll take $110 + post.

Ebay is still getting some good prices on these so you can recoup your dollars if it's not the right one.

Your choice if you want to try get a bargain here first, if not, i'll just put it up on eBay...

Edited by YASIDI
sonicii Veteran

sonicii

Posted
Posted

You can download the install/user manual here

http://usaspec.com/userfiles/editor/file/pa15infi_20100120_webuse.pdf

it also suggested the PA15-INFI connects to the satellite radio unit, but to use the PA15-NIS if you don't have satellite radio as it connects to the back of the stereo HU.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • GTSBoy
      Finding E-30 & E-85 in Sydney

      By GTSBoy · Posted

      This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...