Jump to content
SAU Community

Recommended Posts

Thought I would post up my thoughts from my last track day on Wednesday @ the QR sprints

Previously every track day I have been to in my V35 I have always left the car in D mode with the PWR button pressed as the triptronic mode was far too laggy to be of any use

I recently had the transgo shift kit installed and was interested to see what sort of a difference it would make

I found that there were some pros and cons when it comes to trying to get your quickest time with the shift kit fitted compared to stock

The kit was good in the fact that I could drive the car like a manual in triprtonic mode and actually benefit from some sort of engine braking + the shifts happened for the most part in triptronic mode when I wanted them to unlike how the auto box behaves when its stock

I also managed to shave .16 off my best lap time however the improvement is somewhat on the small side that it could be attributed to a number of factors other than the shift kit

The negative, although I considered it more fun than negative was that the harder/faster shifts turned the car into a powerslide machine if I wasn't careful or more so if I wanted it to when shifting from 2nd to 3rd. This was with 245 Toyo R888 semi slicks on the back :woot: not so good for lap times however

I'm half keen to take the car to a Friday night drift session with some stocko 17's on the back given how easy it was to slide with the semi slicks on

Don't forget I am running an LSD unlike 99.999% of the other auto V35s out there

Link to comment
https://www.sau.com.au/forums/topic/413332-transgo-and-the-track/
Share on other sites

Luckily I had AWD, it loved the track, for about 2 laps before the trans went into overheating limp mode.

I don't think I would take a stock valve bodied car to the track though, the clutches would slip badly imo, causing more heat. Do you have a large trans cooler?

Have never been in limp mode cars been to 9 or so track days with around 20+ laps a day

Do run a trans cooler, dont think you would call it big but you can see the size in the pic + I run the best bang for buck cooling mod by removing the grill at the track so the car gets max airflow even tho it causes more drag

Also note that my tranny is going to be dealing with a lot less power than yours given you make double the power I do!!!

post-9102-0-07887700-1352383286_thumb.jpg

Edited by 180 wanabe

Don't forget I am running an LSD unlike 99.999% of the other auto V35s out there

Hey you keep saying this.......but every coupe that I have done a Transgo kit with in Sydney has had an LSD. Infact I am pretty sure it is standard equipment on manual or auto. The only difference being that the manual runs a 3.538 diff ratio and the auto runs a 3.327(or something).

Who said that the auto's don't come with LSD?

With the RE5 the line pressure is variable, meaning at light throttle is shifts silky smooth but when you plant it the shifts are firm. Definitely great for daily duties but it needs to be installed as per instructions, something professional transmission repairers seem to have a problem with.

The trans can be a little clunky compared to normal, not all the time just the occasional harder shift at light throttle or sometimes when dropping it back a gear. Nothing to worry about though. The clutches will last much longer without the drawn out slop into gear the factory valve body has.

Which suburb are you in Norby?

id be interested to know what the transgo is like for daily suties? I.e ido a lot of stop start driving, does it thunk between 1st and 2nd with little throttle?

mine isnt transgo brand (its custom made), and it does hit second quite hard regardless of throttle position. but this is in a 4 speed...

Custom made means it has some locally wound springs shoved in the place of the stock ones. This does not = shift kit. Yes it bumps up the line pressure but... Transgo have obviously spent a lot of research dollars sorting these kits out, replacing various pistons, adding valves and upgrading springs, all of which gives it the perfect crisp shift imo. I'm certainly glad my transmission specialist didn't cheap out and manufacture his own parts.

id be interested to know what the transgo is like for daily suties? I.e ido a lot of stop start driving, does it thunk between 1st and 2nd with little throttle?

im in Croydon North, im actually considering doing this mod. Just realised today the paint on my bonnet has been repainted and is all now peeling... if it isnt one thing its another with this f***ing car... i still love it though

Custom made means it has some locally wound springs shoved in the place of the stock ones. This does not = shift kit. Yes it bumps up the line pressure but... Transgo have obviously spent a lot of research dollars sorting these kits out, replacing various pistons, adding valves and upgrading springs, all of which gives it the perfect crisp shift imo. I'm certainly glad my transmission specialist didn't cheap out and manufacture his own parts.

Pretty sure MV Automatics are a bit more detailed than that

Hey you keep saying this.......but every coupe that I have done a Transgo kit with in Sydney has had an LSD. Infact I am pretty sure it is standard equipment on manual or auto. The only difference being that the manual runs a 3.538 diff ratio and the auto runs a 3.327(or something).

Who said that the auto's don't come with LSD?

I was sure I had found something about the diff specs of different V35 cars a couple years back. I know that the old diff in my car was crap and constantly peg legged at the drags/lit up the inside wheel when going around a corner at the track

If you can find an auto v35 that can throw down 2 black lines at the same time with the stock diff ill take my hat off to it who knows maybe a factory option, either way viscous sucks balls

copy pasted this from another forum:

2003 sedans didn't have an option for VLSD

2004-2006 sedans had a sport package option which came with VLSD

2007 sport sedans have VLSD, base & journey have ABLS

2003-2004 coupes had VSLD if it was a Performance Wheel and Tire package option, which meant 18" wheels auto or manual.

2005-2007 coupes only those with the Sport Suspension Package had VSLD

*The 18" wheel option for 05/06 is only that, wheels and tires

VLSD became part of the Sport Tuned Suspension package for 05/06*

Pretty sure MV Automatics are a bit more detailed than that

You hope.

I can guarantee they haven't put the same amount of R+D into their valve body upgrades that Transgo have. All I can go by is the local 'specialist' that makes his own springs, they aren't anywhere near as refined and simply bumping the line pressure gives clunky changes. If you are happy thats great but the RE5 is a completely different gearbox...

either way viscous sucks balls

And a two way doesn't? Give me a new tight oem Viscous lsd any day over a clunky mechanical. (for street)

There is no adjustment as far as I know, they will probably need to take the shims out from behind the line pressure spring in the valve body.

Perhaps a slightly thicker transmission fluid may help slow the clutch actuation down?

The diff option list above is for USDM

Best I can do.

Unless you've got a manual or an auto with 'sport package' then only way you'll know is by jacking it up and throwing it in nuetral.

Open diff's can twin up in a straight line though - my R31 had an open diff, and from a standstill it would light up both - have videos from the drags to show it.

Corners were a different matter though.......single peggers all the way!

And a two way doesn't? Give me a new tight oem Viscous lsd any day over a clunky mechanical. (for street)

I've had cars with open, viscous, 2 way and helical lsds and I'd say the best all rounder is the helical

Nothing puts hairs on your chest like going around a large roundabout in the wet with a nice tight 2 way :P

I owned a celica twin cam powered KE30 rolla with a migged diff for a few years, you get over it pretty quick, especially in winter. My favorite diff in the wet is the single spinner, no chance of stepping out with spider gears front and rear. AWD FTW. :)

Best I can do.

Unless you've got a manual or an auto with 'sport package' then only way you'll know is by jacking it up and throwing it in nuetral.

Open diff's can twin up in a straight line though - my R31 had an open diff, and from a standstill it would light up both - have videos from the drags to show it.

Corners were a different matter though.......single peggers all the way!

hey mate just a quick noob question,

when I jacked my car up on a hoist, and in N, the rear right wheel spins by itself, if I put my hand to it and hold it still, the rear left wheel starts spinning,

what sort of diff do I have?

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is there a diameter difference in the stock to Nismo? If so, the weight alone won't be indicative when comparing flywheels of the same diameter, since the radius of the flywheel acts on the moment of inertia with a square factor, where as mass is linear. Roughly going from a 4.5kg flywheel with radius 20cm, to a 9kg flywheel with radius 14cm would see them act the same. This calc is just here to act as a brief numbers comparison and reflects no actual RB flywheel diameters etc. it also assumes even weight distribution (thickness) throughout.
    • It seems this could be due to a restructure/team direction change... Or... You're working with a different category of vehicle... Or you've decided you'd rather be able to play with your own cars again...   I'm hoping the latter...
    • had 4 weeks off over xmas and well did some stuff to the shed and BRZ, well short of is I don't work full time in supercars anymore as of yesterday.........
    • Did you get any down time over Christmas, or have you had any since to play with this? Or have you given up and are trying to get yourself a second hand V8SC instead?
    • A random thought I had just before I hit "Submit on this post". If brake fluid, in a container in my garage that has never been opened goes bad after 18 months, why can I leave it in my car for 24 months in an "unsealed container"... Secondly, some other digging, and brake fluid manufacturers seem to be saying 5 year shelf life... Me thinks there line on 18 months for an unsealed bottle is pretty much horse shit marketing spin. Kind of like how if you drive a car and don't run a turbo timer your turbo and motor will die horribly...   Where I started on this though... Someone (me) started down a bit of a rabbit hole, I don't quite have the proper equipment to do Equilibrium Reflux boiling per the proper test standards. I did a little digging on YouTube, and this was the first video I found on someone attempting to "just boil it". This video isn't overly scientific, as we don't have a known reference for his test either. Inaccuracy in his equipment could have him reaching the 460 to 470f boiling point range in reality. In the video, using a laser temp gun, he claims his Dot3 that's been open in his florida garage for over a year gets to about 420 to 430 fahrenheit (215 to 221c) Doing some googling, I located an MSDS for that specific oil, and from new, it claims a dry boiling point of 460 to 470f. Unfortunately they don't list a wet boiling point for us to see how far it degraded toward its "wet" point. While watching it I was thinking "I wonder what the flash point is..." turns out its only 480f for that specific brake fluid....   As for testing the oil's resistance, I might not be able to accurately do that unfortunately. Resistance level will be quite a LOT higher than my system can read I suspect based on some research. However, I might be able to do it by measuring the current when I apply a specific voltage. I won't have an actual water % value, but I'll have some values I can compare between the multitude of fluids. I'll run some vague calculations later and see if I should be able to read any reliable amount of current. These calcs will be based on some values I've found for other oils, and see how close I'll need my terminals together. From memory I can get down to 1pA accuracy on the DMM. I don't think my IOT Power Tester has any better resolution.    
×
×
  • Create New...