Jump to content
SAU Community

Recommended Posts

Hi,

I have a R33 Series 2, fairly stock apart from full 3inch exhaust, cold air pod and running 9 pounds boost.

Car was running fine up until a week ago, i was driving home from work and all of a sudden it felt like I'd lost a cylinder. Car started to shake, sounded like a Subaru and lacked power. This happened after about 4 minutes of driving, the car had been off for about 9 hours previous (so it was a cold start). I was on a busy road at the time and couldn't immediately pull over so drove for a further 1 or so minutes and pulled over, whilst in the process of pulling over the car came good again as though nothing had happened. Continued home - a further 40 minutes or so with no problems.

Since, every time I drive the car from a cold start after about 3-7minutes I get the same issue - once warm no problems at all.

I've tried the following so far:

- change the spark plugs, no different

- Checked the coil packs (Yellow Jacket coils that have done about 20,000KM's since i put them in). No noticeable signs of any damage that I could see

- Removed and cleaned the AFM with contact cleaner. Idle is a lot better (used to jump / spike at times) which it hasn't done for the last day or two since I cleaned the AFM

Issue still remains. I'm handy and willing to tackle this but don't really have the knowledge of what I should be looking at next. I've done a lot of searching around and reading but can't really find anything quite the same. As the issue disappears again after a a couple of minutes it says to me that it isn't a spark problem? Sometimes it will happen, last for a minute or two, go away for a minute or two and then start happening again for a further minute or two.

Some sort of loose connection? But why only when it is cold?

I'd be really happy to hear any suggestions on what I should look at next? I'm also quite stuck as the car is my only mode of getting to work and I'm worried I'm going to do some damage if I can't repair this quickly.

I'm in the south east of Melbourne and will go to a mechanic if I really need to.

Sorry for the long post.....

Thanks,

Dean

Thanks for the suggestion, I'll check this out tonight a bit more closely and see what I can find - if anything.

Does anyone have a breakdown of the steps that the skyline goes through as it warms up, as this issue is only present when cold I'm guessing that there is a part that is only used at these low temps or the faulty part changes in use as the engine warms up. Does that make sense? I don't know whether such info exists or not, I'm grasping at straws maybe....!

Any other ideas I'd be keen to hear.

Faulty coolant temp sensor maybe, it could be reporting the engine being warmer than it actually is, so leaves cold start enrichment too early.

Last night i unplugged the coolant temp sensor and took it for a test drive this morning, I did not experience the issue for the first time in the last week or two. I'll go for another test drive tonight once the car has cooled down again and see how it goes.

I'm really hoping it isn't the head gasket, because that's a very expensive repair isn't?

I had this exact same problem. It was the yellow jackets. Hard to diagnose coz it only happens in a 2 minute window and then gets dissapears. I installed nissan data scan and did an active test switched off cylinders until i found the one which wasn't firing. Swapped out that coil pack with a stock one, problem gone.

I had this exact same problem. It was the yellow jackets. Hard to diagnose coz it only happens in a 2 minute window and then gets dissapears. I installed nissan data scan and did an active test switched off cylinders until i found the one which wasn't firing. Swapped out that coil pack with a stock one, problem gone.

Thanks, I'll organise the purchase of datascan and check this out. For a 'standard' person is the software easy enough to use?

I'm also going to replace the coolant temp sensor, they are very cheap and seems an easy thing to do.

Can you purchase coil packs separately? If it is just one coil pack that is faulty.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
    • Hello. I have an a31 cefiro but since I am in Turkey we have a CA20S engine. I did some research. Then I found that I can swap with a ca18 but when I heard that it has the similar substructure as the s13. I thought I can swap with an sr20 because the sr20 was used with the s13. So can I easily swap the sr20 on my cefiro or is it difficult? 
    • I used to love stock take. I used to take f**k of a lot of stock. /Rodney Rude.
×
×
  • Create New...