Jump to content
SAU Community

Recommended Posts

Recently put a r33 rb25de in our r32. Starts fine and idles perfectly however as soon as you go to drive it, it lacks power under throttle and runs "spluttery" ? Have replaced afm, coils, o2 sensor, fuel filter and pump and still no improvement. We are stumped as to what the problem might be. The problem"spluttery" driving feel seems to be proportional to accelerator position and not rpm. Have checked and adjusted tps and have app plugged in.

Any help greatly appreciated!! :-)

Link to comment
Share on other sites

  • 1 month later...
  • 2 weeks later...

from what youve described im having the same issue with my rb25de in my 33. ive had a couple of mechanics look over it and they all think its the injectors. but they want close to 400 bucks to remove them and clean them for me. so tomorrow im pulling them out and going to d.i.y clean them. ill let you know if it helps at all. i also re gapped my plugs and it ran better for a while. if your running bosch plugs through them to the shit house and get a set of ngk.

Link to comment
Share on other sites

normally i would say that $400 to pull them out and clean them is a bit much, but they are a pain to get to. i'd get a price on getting them ultrasonically cleaned if you pull them out yourself. that way you know that they are actually cleaned properly. when i was looking at getting my ones done a few years back, a mates workshop charged about $35 an injector to clean. i think that was including pulling them out though, but it was on something with easier to get to injectors than a rb

you may just need some new o-rings as well

Link to comment
Share on other sites

  • 5 weeks later...

Ok so basically car has been garaged while we moved house and did a few body repairs. Decided to try again. We double checked wiring, plugs, spark plugs, fuel pump, afm, still no luck. Decided to play around with the timing, set to full tilt one way and actually managed to have it running. Not great but enough to get from a to b. But....inevitably the problem came back.

Have just gone through with a bit of help from a friend and set correct rpm and timing and the problem is even worse. Its not even livable now.

Really clueless as to the cause of the issues and with baby due in 8 weeks i really need my car going! Any more ideas or suggestions all greatly appreciated!

Link to comment
Share on other sites

have u had the injectors cleaned? if u changed the timing thingy so it was running rich as balls that would have fixed the problem. seriously it takes me 15 mins to have my fuel rail out and then u can get them flow tested pretty cheap. i recon its your best bet atm.

Link to comment
Share on other sites

I have the same issue with my r34 is draining too much petrol atm and lost alot of power. so ill be driving around in a eg civic till its fixed lol, been told its my coilpacks witch i havent got around to change yet as its a pain to get to them arg damn neos lol

Edited by Johnie
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
    • Id like to race in the US i think alot of those track would suit me   For the s15? Youd be stuck between club sprint and the new Open Am wouldnt you depending on how much interior you have left in
×
×
  • Create New...