Jump to content
SAU Community

Recommended Posts

Hey guys getting a tune on my car soon and got recommended to put iridium plugs in it. Just wanting to know what you guys use what you think best option is and your opinions it an Rb25det with work I'm hoping to be pushing around the 400hp mark.

Thanks for any help.

Link to comment
https://www.sau.com.au/forums/topic/413743-best-spark-plugs-to-use/
Share on other sites

Iridiums are fine, they are just harder to gap down. Some say you will gain a little power from going copper but the trade off is you may need to change them every 10,000k's or so.

Iridiums can last 80-160,000k's if you keep them cool. They still melt if abused.

Iridiums will still lose some effency after 10-20,000 klm.

If you service your car every 5,000 klm put in fresh coppers every second service, on every other service pull the plugs and clean the electrodes with some fine emery paper and regap.

I have always done this and never had a problem even running 380 @ 22 psi.

Iridiums are designed for lazy people who do not service their own car, the less plug changes over the 100,000 saves some money but will effect performance.

I want all my killer wasps all the time.

The $30 or $40 dollars every 10,000 klm makes good performance sense to me.

I don't think we've talked about this topic enough so I'm going to disagree with all of you.

Please continue

I know this topic has been done to death but if you find my method flawed please enlighten me as I am always open to opinions that may prove me wrong.

I may be old but Im still open to some learning.

If I say yes will the thread continue?

A yes with a reason and I shall never be seen in this thread again.

A no with a reason and I still wont be here again because I have said what I believe to be correct due to many hours of searching and my own prior research on spark plugs and correct gap sizes.

:P .

Gold :thumbsup:

Thankyou for clarify this issue, its good when a subject matter expert helps out a newbie with a quick and to the point explanation, its good to see them help people with their wealth of technical know how, I would say its even good for business.

Thankyou for clarify this issue, its good when a subject matter expert helps out a newbie with a quick and to the point explanation, its good to see them help people with their wealth of technical know how, I would say its even good for business.

There is a thread a week about spark plugs.

Answering the same question 50 times a year doesn't help anyone. It just adds to the problem. There was a thread only last week and it was answered quite well I thought.

And yes I was being sarcastic but I'm like that sometimes. The people that know me would usually laugh, those that don't might think I'm a prick. I don't mind.

I help the ones that I can help, I don't help the ones that don't help themselves by searching first.

To answer your first question, there is no flaw in your method. It's sound advice and I feel that the question was answered appropriately so I made a very clear sarcastic remark to make a point. I just didn't know I would be arrested for it :D

Spark plug that sparks!??

U ask stupid questions u get stupid answers like that. If u had not been soo lazy & used the search function, spent s little time reading u would have found ur answer. As stated by others, this topic has been done to death!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi again all, I’ve tried doing some searching on the topic but couldn’t find the answer I’m looking for.   I deleted my clutch booster because it had an air leak and was squealing like a hog, and now my clutch has very poor pedal feel and the friction zone is way too small, so I believe I need a bigger diameter clutch master cylinder to compensate for not using the booster. I found a Wilwood option that’s 3/4” for a good price and will fit my 3AN clutch line, but all the firewall adapters I see online such as RB factory or Chase Bays are listed as RWD only (GTST/GTS). Link below. https://rbfactory.shop/products/nissan-to-wilwood-girling-clutch-master-cylinder-adapter My question is if these adapters will also fit a GTR, and if anyone has experience using a 3/4” CMC without the booster, my clutch is a Nismo coppermix twin plate.   Thanks, always appreciate the advice!
    • Catching up on a post, I've replaced the external shark fin with a small 4g antenna (no further drilling, just a 1mm embiggening of the existing hole, and run that to where the dual battery models have the battery in the left rear guard.  No idea what the factory antenna did, but removing it had no impact on anything I use, according to the US manual the GPS antenna is in the dash and it still works fine Also ended up stealing battery power from one of the amps and ACC power from a unit nearby to add an ACC relay to power it. The mounted the booster, wifi, power socket and antenna splitter in the rear left guard out of the way, all out of site with the boot trims in
    • What drama? The only drama you're going to have is the near constant work to maintain all those sphericals. I only have sphericals in my front caster rods and front upper CAs (because both of these are near compulsory in an R32). I have had the front arms out of my car 34 times already this month, and if the new replacements arrive today, I will have them out and apart again tomorrow. Chasing clicking and clunking that comes from sphericals being a.....poor choice for a road car. Moisture and dirt are not their friends. I have been contemplating a change to my rear subframe that would require me to use sphericals in my lower CAs. And.....I don't want to have them that close to the road.
    • Did you need anything else you've already done? If you had it before... and liked the changes after, then supposedly it'd be more of the same. The idea about most suspension arms is to tune geometry that the OEM arms max out at/can't handle because they weren't designed to have the car setup in such a way that 'looks good'.
    • I have replaced everything on my r34 including suspension to Miester R, all rear subframe bushes to poly, all arms to metal adjustable and same in front.   only thing I haven't touched is the front lower control arm. Should I? what improvement can i expect ? I mean the one on the link below?   Car drives perfectly, it is just me thinking everything is either puly bush or hard bearing type so should also do lower control arm front but do I really need it ? https://www.japspeed.co.uk/product/suspension/adjustable-arms/nissan-200sx-s13-s14-s15-skyline-r32-r33-r34-adjustable-suspension-front-lower-control-arms/?gad_source=1&gclid=Cj0KCQiAo5u6BhDJARIsAAVoDWs5V_PauQPf0kx3zFCaA4tOC9Q7JSIsfJWma_jAPN2f1sJA686djOwaAidgEALw_wcB
×
×
  • Create New...