Jump to content
SAU Community

Recommended Posts

just picked up a silver s1 gts-t for stripping, running gear is on hold, dash/surround/interior mostly gone

cusco adj coil overs $1000

apexi massive exhaust $300

headlights $350 pair

heaps of other stuff will update tomorrow

car is located northern suburbs S.A

post-4329-0-36080500-1353060694_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/413818-r33-wreck-silver-s1/
Share on other sites

front calipers and rotors $350

tailights $140 pair

elec mirros $20 pairs 2sets

boot with s2 wing $80

window regs and rails $50 each side

s1 bonnet $100

Gaurds $40

Ariel $40

rear 33 nissan strut brace $150

stock cooler and piping $80

stock rad $50

heaps of stuff here :P

just got in contact with a mate he cant buy the running gear for a couple weeks

i want this gone asap as another car has popped up may sell complete for the right price

pm me if your chasing a running gear package or possible missile/tracker complete :P

UPDATE this actually has vct running gear so its first of the S2 engines, (no ignitor, pink label afm)

may sell cheaper without engine loom as i need a s2 loom for my project :P

may even split engine and box if i get buyers for each (i need clutch/flywheel for my build) can work out deals :P

$280 headlights

$300 front calipers n rotors

$600 17" meshs (plus rims to keep my shell rolling)

$100 taillights

$60 boot linings/carpets

$80 boot with s2 wing

Complete aircon engine bay set up $250

$1000 rolling straight shell (engine isnt out yet)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This piece is obscenely discontinued. I honestly hate the frameless window design because the rubber gets stressed and the guides as well every time you open and close the door.
    • I wouldn't be concerned at all, other than to suggest having them flow tested when you receive them to confirm they are reasonably similar, and then put the highest to lowest flowing ones in cylinder 6,1,5,2,4,3
    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
×
×
  • Create New...