Jump to content
SAU Community

Recommended Posts

I am currently stripping my car as I have no licence and lost all interest in imports, here is the engine

Rb26DETT Build and inclusions as follows;

Run in and was tuned to 14psi has done 2000km, made almost 400HP at @ 14 PSI

Mild Port polished head fully reco'd replaced all retainers

Tomei 1.2mm headgasket

Genuine nissan gaskets used throughout rest of build

Tomei Oil restricter in block

Gold painted cam covers

Sard 700cc injectors

Fitted with D-Jetro map sensor nipples can be blocked if not using

Oil drain fitting at rear of head, braided line to sump

All new silicone heater hoses and vacuum lines

Polished Plenum and twin turbo pipe

Water Pump was replaced as well as T/Belt tensioners etc at build

Block decked and machined, bored and honed for 20 thou oversize pistons

Build Blueprinted and all measurements adhered to

Eagle forged rods

CP forged Pistons 20 thou

R34 GTR crankshaft

ACL RACE series bearings

ARP Headstuds

Jun Sump baffle with steel trap doors

All new brass Welsh plugs, block painted in black enamel

Motor included all listed minus parts below $6500 (Whole motor plus intake side minus turbos and accessories)

Here are the extras add prices if wanted with package, currently it is all together still

HKS 2530's brand new when fitted to motor $2000 (Still on engine, if separate sale extra for fittings etc)

Nismo Engine Mounts also new at fitment $100

R32 GTR engine loom complete for $250

Have alternator and Pwr steer pump plus belts for $80 a set

Splitfire coil packs and loom for $450

Feel free to PM txt or call if you would like to mix and match or if you want a cheaper price i can for example change injectors to std etc, I have heaps of other parts for sale as I am stripping my car so dont hesistate to ask. Can also organise fitment of any other parts you may have or want to purchase towards your setup, I am a trade certified mechanic.

Johnny 0414596256 Gold Coast (North)

post-44496-0-53375800-1353477557_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/414129-rb26dett-forged/
Share on other sites

genuine nissan oil pump long collar model to suit, motor was built by jono milentis (formerly speedtech) here on the coast, all machining done by robbie abbott (Abbotts engines) I myself designed the build.

Link to comment
https://www.sau.com.au/forums/topic/414129-rb26dett-forged/#findComment-6682155
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...