Jump to content
SAU Community

Stag Cutting Out?


twins777
 Share

Recommended Posts

hey guys,

I have recently pulled the stag apart and detailed the engine bay, and put it all back together on the wkend it started first shot no worries but when I accelerate and take my foot off the gas the car struggles to idle and cuts out sometimes.. I removed the plenum, throttle body, rocker covers etc.. just wondering if anyone has had this problem at all.. any info would be great..

cheers guys

Link to comment
Share on other sites

Did u plug ur idle control solenoid back in? Double check all plugs and hoses that you touched and even stuff u didn't, it's posible u left something undone or knocked it loose. If it only started playing up after u touched it then there is a 99% chance it's something u have done

Link to comment
Share on other sites

hey guys,

thanks for the reply's.. I have looked over the car every where.. maybe I put vacume line on in a different spot somewhere but pretty sure there all back in the same spot hopefully.. :( the only vacume line that I wasn't sure of is the one under the bov??

Link to comment
Share on other sites

hey,

really I've had this on here for over a year and never had a problem.. only until I pulled the car apart.. it doesn't do it all the time only when u boot it and take your foot off and stop sometimes it cuts out..

Link to comment
Share on other sites

hey guys,

I put my standard bov back on and the car still cut out after u gas it and take ur foot off doesn't do it when free revving.. does anyone know how to reset the ECU and will it affect my nistune..

cheers guys

Link to comment
Share on other sites

hey,

yeah my car drops to bout 500rpm then cuts out at low speed.. running rich too.. drove it in triptronic mode doesn't seem as bad.. prob have to go back to the tuner and get a diagnostic done on it to see what is wrong..

Link to comment
Share on other sites

Its not the BOV; the BOV story rings some truth but its right up there with coilpacks being the fix for 90% of problems according to the forums...theres likely still an underlying issue.

Definitely find the tutorial and give the AAC valve a clean. Made a big difference when we had low speed/snap throttle closed stall issues with our S1. Curiously replacing the O2 sensor also helped, though ours appeared to be the original item.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...