Jump to content
SAU Community

Recommended Posts

HI all,

So i just recently got a second hand engine installed after i blew my last one up..

all is well except for this really annoying cough/splutter on a cold start just off idle...

if you try and put any load on the engine when it is cold (around 1000rpm) it will cough and splutter to the point of stalling.

i recorded a video so you will know what im on about:

i have replaced:

Leads (top gun)

plugs (NGK)

Air Regulator (off another motor)

i also took the injectors, fuel rail and afm off my old motor which had no issues and it still does it.

if its worth mentioning:

1. Car is a manual conversion (never had issues before)

2. all is fine when it is warm

3. it seems to idle a lil low when cold(around 800 - 900rpm, could be more or less as i have a sticky tacho), but a little high (1100 rpm when warmed up)

Link to comment
https://www.sau.com.au/forums/topic/414953-r31-rb30e-cold-start-issue/
Share on other sites

I'm not sure how R31 ecus work, in a R32 and beyond I would suspect the coolant temp sensor (not the one that feeds the dash cluster, the one that feeds the ECU), when not functioning it might not be going into the cold start map (richer than the normal one).

  • 2 weeks later...

i had issues similar to this an adjustment to the TPS cleared it up

so i have tried so far:

1, Spraying crc contact cleaner on the AAC Connector, Both sides of the coil, Air Reg connectors, tps connector......

2. tried having a play around with the tps, fully clockwise it idled lower, didnt fix the issue with the spluttering..fully anti clockwise the issue wasnt any better but it idled higher

3. unplugged afm and it idled like shit, wouldnt rev etc so i know the afm works.

im baffled as to what it is

if its not that then keep trying other similar things, 31s are getting old now and most of them have had the tits revved out of them by p platers and messed around with a lot

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
×
×
  • Create New...