Jump to content
SAU Community

Where to get Skyline Serviced


Recommended Posts

Have to give thumbs up to Marc at Discount Tyres Belconnen, had the car breakdown at the start of the week. Fitted me in, fixed the problem, reasonable charge, and explained exactly what the problem was and how it was fixed.

Great folks - highly helpful and recomended.

These guys also install Sydney Kids suspension kits, do the settings.

Link to comment
Share on other sites

From a soarer perspective, Trojan rate very highly in my books. AutoTech dyno tuned her last year, which was a great tune; however, he told us he is cautious and wouldn't run anymore than 15psi unless 600cc injecters were fitted. As a result of the dyno shootout at Jakes Performance, I will be going there to get some tweaking done. For normal servicing/problems though, I go to Neil Griffiths at Rush Imports in Queanbeyan, as he is the soarer/toyota guru of probably the whole of Canberra. Despite my previous 'loyalty' to EVO Motorsport; they lost me when Stu forgot what spark plugs to use in the soarer when he did a minor service awhile ago. Rush wasn't open so he asked EVO and the ones they recommended were totally wrong and left her running rather rough until Neil fixed it.

Does anyone bring their Skyline to Neil??

I used to bring my car (VL) to Neil many many years ago and always found him good...though last time i spoke to him he didnt think much of Skyline drivers

Link to comment
Share on other sites

  • 1 month later...

i got a major service at integra automotive in queanbeyan yesturday his a pretty awesome guy to deal with but he used all the expensive shit 4 my car but i wasnt bothered by that to much but i will be going back to him 4 services n repairs

Link to comment
Share on other sites

i know this isnt exactly the best place to ask, but im not an uber fan of NS.com

anywho, just wondering if anyone can recommend for a general service on an S13 Sr20det? just need oil changes, intercooler piping cleaned out (has oil in it, and pops off when boosting even after tightening the rings :laugh:) and just a general clean up...

Link to comment
Share on other sites

do the piping yourself should be easy if it keeps popping off :laugh: i found a couple of posts about what to use to clean it up

do the 50/50 mix and block up the end shake around a bit empty, repeat till clean. Then let it dry before putting it back on. Also go buy some decent clamps if they keep coming off.

http://www.skylinesaustralia.com/forums/in...showtopic=69501

http://www.skylinesaustralia.com/forums/in...=135634&hl=

http://www.skylinesaustralia.com/forums/in...=134057&hl=

Servicing anyone should be able to help you out maybe autotech, or trojen if you want to be particular...

Link to comment
Share on other sites

Hey Beau, i know what you mean ay, sometimes a bit... strange there.

Anyways, a few options:

- do it yourself, i (or most others here) can show you how

- Most workshops are capable of a general service, still, see if you can find one you're comfortable with. A few people here will be able to recomend you to somewhere good.

Link to comment
Share on other sites

yeah im gonna be attempting the oil change meself tomoro, with the sisters BF. shall see how that goes.

thanks for the offer guys, i still need to clean the intercooler piping, and get some stronger ring thingys, and im lost on doing that myself :D

will most probably ask someone to hold my hand while cleaning the piping as i dont wanna f**k it up...

Ill PM Around anyway, Cheers guys!

Edited by SKYLVIA
Link to comment
Share on other sites

  • 3 weeks later...
well i'm up for my 100K service in the GTR. Timing belt has already been done - any advice on where should I go?

i have a powerfc yet to be installed - maybe i could combine the two to save $$$?

And the answer is..... Autotech Fyshwick

Link to comment
Share on other sites

Big thumbs up to Trojan who did my 100k km service.

Fixed what I wanted and a few other bits and pieces and got a 25% increase in fuel economy with seemingly more power and response.

cheers mate. can you tell me how much it cost? (pm is fine) also i'm assuming they dyno'd it?

Link to comment
Share on other sites

cheers mate. can you tell me how much it cost? (pm is fine) also i'm assuming they dyno'd it?

They didn't dyno it as they didn't touch the tune at all. Car has been tuned by DTS and Autotech and not overly happy with the job either place did. DTS tune was on the car when I got it and was horrid. Peter at Autotech did a good job ironing out many of the issues but left it running far too rich (which in hindsight may probably caused by the intake/exhaust leaks).

Cost was significantly higher than for a standard 100k km service as I had a lot of labour to get the turbo exhaust gasket replaced. There was also additional costs for a new water pump and other odds and ends that you might not necessarily need replacing.

Final price was $2200 which was a little higher than what I expected. But I do have an itemised bill and all the old parts they replaced to confirm they didn't charge for work not done.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...