Jump to content
SAU Community

Ignition Steering Lock Mechanism And Telescopic Adjustment

jonathon

By jonathon,
in General Maintenance

 Share

Recommended Posts

jonathon Enthusiast

jonathon

Posted
Posted

Hey guys,

I have pulled apart the steering column surround to have a look at why the telescopic adjustment is not working (dying for another inch of steering reach!) on my R32 GTR.

Once the surround was removed I have discovered that the steering lock mechanism/bracket is broken - therefore not allowing the steering to be locked.

post-32397-0-81392700-1355386307_thumb.jpg

post-32397-0-69329500-1355386331_thumb.jpg

I have no idea how to remove the damn thing as there are no screw/bolt ends?! I'm guessing they are security bolts of some sort, and I could drill them out.

post-32397-0-73088300-1355386525_thumb.jpg

The question is

- once removed how do I bolt on a new one?

- can the ignition barrel be swapped to a new bracket so I can keep the same key (to match boot/doors etc)?

Also - why on earth wont the damn steering adjust reach (tilt works)?

Cheers

mad082 Grand Master

mad082

Posted
Posted

i don't think skylines have reach adjustment. i know my r33 didn't.

as for the ignition barrel, yes you can get a new one that is keyed the same as your old one. there should be a number on your old one which you could take to any decent locksmith (not just one of those key cutting places) and get it sorted

jiffo Mentor

jiffo

Posted
Posted

Yes 32's have up/down and in/out adjustment.

From memory it's a big job to remove the whole column, some dreadful stuff down at the bottom.

The bolts that mount the column to the bodywork are specially designed to shear in an accident, I don't think they "undo".

You photos don't show the adjusting levers, just the broken IGN lock.

jonathon Enthusiast

jonathon

Posted
  • Author
Posted

hey guys - thanks for your replies.

Turns out that it looks like someone has broken the steering lock in a previous life - bending the steering column sleeves that allow for reach adjustment.

So she is seized up and non-adjustable - simple fix was a boss kit spacer to get some more reach!

H4x - I ended up drilling the damn things out! but I tried your method on the new barrel (as the bolts were still in there) and it worked a treat!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      WTB noltec r32 front upper (camber) arms

      By GTSBoy · Posted

      I swear at my GKTech ones every time I have to take them apart and replace a spherical. But I wouldn't swap them for anything else. They absolutely slay every other option, at least in terms of how they actually work. You sure you don't want to live with bearings? I mean, they don't have "ball bearings". They are rod ends and sphericals throughout. Tough as nuts, even though I have found more than one way to wear them out.
    • The Bogan
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By The Bogan · Posted

      From when I was looking at getting the 86 engineered for the turbo, the joint said to put in a few euro 5 or 6 cats, then tune the car on a nice clean E85 tune When I was looking at a turbo for the MX5, it was basically the same thing, a couple of cats and a nice clean tune Although, it will depend on the year of the Jeep IRT emmisions standards required, and what mods are done, especially if it has a newer engine installed that requires a higher Euro
    • GTSBoy
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By GTSBoy · Posted

      Yeah - but it's not actually that easy. There are limits for HC, CO, NOx and particulates. Particulates shouldn't be a concern in any petrol engine unless trying to comply to the very latest Euro standard. But getting a tune right so that all the others stay within limits AT THE SAME TIME is not a trivial exercise. You couldn't possibly get it right by just guessing at the tuner's dyno, unless he had a 4 gas analyser up the pipe, which is not often the case these days. It used to be. Every decent shop that did "tune ups" (as opposed to tuning) would have a 4 gas analsyer. Perhaps there's still quite a few of them around these days. But most "tuners" are only watching O2 and power readings.
    • Shoota_77
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By Shoota_77 · Posted

      Slight segway but the most expensive part of the whole thing which I would have thought would only be required for an engine size/type swap, not a VIV test, is emissions testing.  That's when you get into the big bucks.  I can't remember the exact price now but I got quotes for the GT-R based on swapping to RB30 (not that anyone bothers doing it legally anymore...) and it was around $4500 just for that alone.  The guy that does them manipulates the tune on the vehicle to make sure it passes.  The cheaper option is to book into Kangan Batman Tafe (I think that's where it was) and hire their tester.  Allegedly you're not allowed in there with the car though so not in a position to tweak anything to make sure the vehicle passes.  I'm sure in this day and age of ultra tuneable ECU's you could get the tuner to program a special efficiency (clean) tune that emits the lowest amount of particulates possible that would pass the test.  It might only make 50kW's but as long as it passed who cares!
    • The Bogan
      Neil's R33 Gts-t Build

      By The Bogan · Posted

      I'm sure he has left signs, or, he is looking down, laughing That's my cunning plan for when I leave, lots of half finished projects, with no rhyme or reason of where I was actually up to, just to keep everyone on their toes
×
×
  • Create New...