Jump to content
SAU Community

Wtb: R33 Coupe Rolling Shell/cheap Complete Car

Mitch130

By Mitch130,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

Mitch130 Apprentice

Mitch130

Posted
Posted

Hey guys, i recently bought a nice r33 and i was hit in the rear quater and write the car off. As it was a new car to me and it was not my fault the accident occured i wish to rebuild it to its former glory,

Im looking for a complete car minus the motor/box as i will be swapping the drive line out of the old 33 into the new shell.

Also, if you have a cheap r33 with a clean interior i would also consider it as i can respray the outside but dont want to chase interior panels. As above driveline isnt an issue.

Must be located in QLD, no accident history.

Please contact me via the email below

[email protected]

Thanks for your time,

Mitch.

  • 2 weeks later...
  • 2 weeks later...
mungy Experienced

mungy

Posted
Posted

Still looking guys!

That's because your asking someone to give you a discount on something that sells easy mate, don't be cheap buy a good shell that will have no problems later on

Mitch130 Apprentice

Mitch130

Posted
  • Author
Posted

Im not asking for any discounts bud, im looking for a stock r33 or something with a dead motor/rolling shell.

I've never asked to pay a discounted rate and i do have the money to purchase said items, so please keep your comments to yourself.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...