Jump to content
SAU Community

Recommended Posts

Ive just got my R32gtst 3 weeks ago. Completely stock, now i hav a full 3' exhaust with a high flow cat.

Im gonna hit Calder drags in the next few weeks and just wondering wat u guys hav found to b the best way to launch ? So far ive tried keeping the revs at about 3500rpm the dumping the clutch the car just bogs, but wen i feather the accelerator at 3000rpm then dump the clutch gets a bit of wheel spin but i do manage to stay on the ass of my mates MR2 turbo (mid mounted engine) untill we hit 2nd then i pull away a bit.

So im just wondering if there's anyone out there that has figuerd out the best way to launch there skyline ?? in particularly the 32.

P.s anybody got any clues on wat i should be doing down the 1/4 ? i have 225's on the rear.

cheers

Link to comment
https://www.sau.com.au/forums/topic/41595-r32-gtst-times/
Share on other sites

Try attaching it to a rocket!

Just kidding!

Depends heaps on your clutch, suspension setup and tyres.

If you don't mind burning your clutch a bit just slip it a little until your away while realeasing the handbrake to limit wheel spin. Don't let the revs go below about 5000rpm.

Stock clutch will probulary fry.

Link to comment
https://www.sau.com.au/forums/topic/41595-r32-gtst-times/#findComment-853183
Share on other sites

Let me know when you are going, im new to Melb and havent been to Calder, and want to run my car as well. Im thinking the first week or two of July.

As for launching unless you are looking to replace your clutch then id take it easy and only briefly ride the clutch with about a 3.5-4k launch, .I would rather go 0.2-0.4seconds slower knowing im looking after my clutch then cook my clutch just to a fraction of a second quicker...

As for times, i suppose a flat 14 for a car with exhaust woudl be a realistic goal.

Link to comment
https://www.sau.com.au/forums/topic/41595-r32-gtst-times/#findComment-856369
Share on other sites

  • 2 years later...
Let me know when you are going, im new to Melb and havent been to Calder, and want to run my car as well. Im thinking the first week or two of July.

As for launching unless you are looking to replace your clutch then id take it easy and only briefly ride the clutch with about a 3.5-4k launch, .I would rather go 0.2-0.4seconds slower knowing im looking after my clutch then cook my clutch just to a fraction of a second quicker...

As for times, i suppose a flat 14 for a car with exhaust woudl be a realistic goal.

i ran a 14.1 in a r32gts-t with exhaust and air filter. using crappy 215 40 17s with street pressure.

The bets way i found of launching was holding the handbrake when staged and hold the car on biting point with boost all ready built up so you have some real power to get off of the line try 4k rpm with this launch then go higher slipping clutch out. but be careful your clutch gets hot and also gearboxes are quite weak so upgrade to r33 box if going to drag a lot.

Thanks John

Link to comment
https://www.sau.com.au/forums/topic/41595-r32-gtst-times/#findComment-2847989
Share on other sites

  • 1 month later...

hey dude

i have a r32 gtst aswell

for me if i have good tyres on its a 4k dump... foot to the floor, i get just that little bit of wheel spin,

but i dnt have the power to keep it spinning... mines pretty stock

if i dont have alot of tread then its a 3500k launch

but if u want what i reckon is the best launch, just ride the hell out fo your clutch, kinda hard to do

i need to ride it without moving forwards

so rip the handbrake up, ride the clutch so boost builds and let the handy down as u take off

Link to comment
https://www.sau.com.au/forums/topic/41595-r32-gtst-times/#findComment-2998846
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...