Jump to content
SAU Community

Recommended Posts

Clearing out left overs in the garage. I'm located in Sydney, would prefer to sell locally but will consider posting.

Contact me via text on 0468 330 099 and let me know what you're after. Am negotiable but within reason.

Turbosmart dual stage boost controller. Whats shown in the photos is included. Chasing $150 ono.

yK0hG.jpg

Drift branded gauges. Water temp and Oil pressure. Comes with oil pressure sender to suit RB. Also electrical wiring for one gauge included. Chasing $60 ono.

cG7qb.jpg

R32 front auto spoiler with the motors. Quite rare, was working perfectly fine, got in the way of my front mount so had to remove. Some scarring on the front and underside. Chasing $250 ono.

noPnw.jpg

R32 gtst front bar. Factory dark blue colour, has a few battle scars and a crack in the front. Cable tie it up if you really need. Chasing $60 ono.

dvtVW.jpg

sDox3.jpg

R32 factory side mount intercooler with piping. Chasing $50 ono.

BXyn0.jpg

R33 GTR Starter motor (from memory) but is interchangable, was going to use on my r32 gtst but didn't need it afterall. Chasing $50 ono.

sBZ5u.jpg

R32 GTST 2 door vertex style side skirts. Brand new, tried to trial fit but they were to tight so never installed them, may need altering to fit. Chasing $120 ono.

vlBey.jpg

R32 GTST 2 door mud flaps full set front and rear. Factory dark blue colour, good condition. Chasing $50 ono.

HGkNT.jpg

R32 ashtray. Front flap/door missing but still better than nothing if you need one but don't mind seeing inside the ashtray. Chasing $15 ono.

8UbwX.jpg

Boost gauge. T-Sport brand reads in psi. Have no idea if this works have never fitted it, came with the car. The plastic garnish around the inside is loose. Chasing $15 ono.

ykCEE.jpg

f0qCG.jpg

Brand new Nissan skyline 1987-1994 aerpro wiring harness for aftermarket headunit. Chasing $15 ono

xKZig.jpg

Edited by dee-20t
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...