Jump to content
SAU Community

pfc boost control kit install

Kinell

By Kinell,
in Engines & Forced Induction

 Share

Recommended Posts

GunMetalR33 Mentor

GunMetalR33

Posted
Posted

So far this is what i know:

1) Connect the Apexi map sensor (included in kit), if you have an r33 find the sensor that runs the stock boost gauge then run a T peice of the hose that connects to it. Then run the hose to the Apexi map sensor. If you dont have an r33 then use the hose that you run your boost guage off. Next you need to connect the apexi map sensor to your PFC (cable included and there is only one in the kit that will fit).

2) Connect the apexi boost solenoid, simply replace the stock solenoid with the apexi one. NOTE, you may have to change the posi of the ports on the solenoid depending on you setup. (see the guide on the US apexi site for the AVCR). You plug the apexi solenoid into the plug that the stock solenoid used. If the plugs are not the same it probably means that you have a solenoid for the GTR and you might have to cut the wires and solder them.

3) Tuning, go to the boost menu on the hand controller. Set the desired boost level in BAR. Go for a run under good load in third gear. If you do not get the boost you wanted then increase the base duty, if you over boosted then retard the base duty. NOTE: If you increase the base duty too much then your boost controller will spike, but if you dont have enough base duty then you wont come on boost hard enough. You dont have to get it exactly right though as the boost controller will learn the right boost curve after a couple on runs.

I am in the process of doing the above and I hope it all makes sense. If you have any further questions about the install then send me a PM. Chances are that I would have had the same problem.

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
    • Dose Pipe Sutututu
      RB25DET Solid lifter conversion

      By Dose Pipe Sutututu · Posted

      If it's for a SR20, make sure it's not the American Poncams, might as well call them Poocams. Had a set in a friend's car, all scuffed up after a few track days. Like the metallurgy Tomei USA used is junk. Went back to JDM OG Tomei Poncams, no issues till now.   Tomei USA is not the real OG Tomei.   Random rant over, fk the US of A, bunch of c u n t s. 
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • pogman
      RB25DET Solid lifter conversion

      By pogman · Posted

      Poncam the world
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
×
×
  • Create New...