Jump to content
SAU Community

Fresh Forged Sammut Built Rb30 All New Sensors, Haltech Ps2000 And 5 Spd Gearbox

STATUS
 Share

Recommended Posts

STATUS Grand Master

STATUS

Posted
Posted

Fresh Forged SAMMUT built RB30 300kw+ capable setup

Full new motorsport prepped (heat and rub proofed) loom with all new connectors on every connection like CAS and injectors etc...

New Top end haltech PS2000 with latest firware etc and tuned by SAMMUT racing.

All new sensors and Ignition leads

New GT3582R

New 6Boost low mount manifold

New Plazmaman intake and TB

New HD clutch and 5 speed gearbox.

Complete setup for sale bolt in conversion, all only done run in kms on dyno. $4k for the LOT... cheap as!

Was built for circuit duties. We have just bought the car and the driveline is not needed as its going TT lS1.

SAMMUT had the fasted outright and the fastest steel 6 cylinder (Rb) in the world (300ZX)

20130107_192745_zps044cc3ec.jpg

20130107_192808_zps5663d054.jpg

20130107_192752_zps7076b90b.jpg

GTScotT Grand Master

GTScotT

Posted
Posted

that is insanely priced....

should sell in a heart beat.

I am assuming the ECU is already tuned and the new owner just needs to install and rock on?

STATUS Grand Master

STATUS

Posted
  • Author
Posted

literally bolt it in and drive, im putting it on the dyno today to check AFR and timing.... im sure nothing will be amiss as they build and tune 6 sec RB'S

post-34927-0-69745300-1357597328_thumb.jpg

GTScotT Grand Master

GTScotT

Posted
Posted

Post the sheet if possible as I'm checking interest with a couple of mates currently.

Its priced too well to let slip.

STATUS Grand Master

STATUS

Posted
  • Author
Posted

Quick question, will this drop straight into a 32 GTR?

it will but this is a single cam.
JimmyRickard Mentor

JimmyRickard

Posted
Posted

Hi trent i emailed you before can you please give me a call or email me your phone number?

cheers

STATUS Grand Master

STATUS

Posted
  • Author
Posted

i may need the ecu so pricing has changed. i may strip it all apart and sell separate. Ive found too many goodies to sell for 4000.

5k for the full shebang or im going to strip it.

5k also includes brand new Di Philippo turbo back exhaust.

luke gtr Grand Master

luke gtr

Posted
Posted

Quick question, will this drop straight into a 32 GTR?

no.

wiring loom will be different.

engine mounts will need mods.

awd sup will require adaptor.

turbo manifold might not fit.

JimmyRickard Mentor

JimmyRickard

Posted
Posted

i may need the ecu so pricing has changed. i may strip it all apart and sell separate. Ive found too many goodies to sell for 4000.

5k for the full shebang or im going to strip it.

Still interested. Please call me 0418 657 612

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Christof
      HK Premier with plans for slight mods, but keeping clean and simple

      By Christof · Posted

      First time visitor and currently getting ready to start work on my HK Premier.  Its all stock, 186 with 3 on the tree.  The only mod i have right now is extractors.  I am hoping to get some guidance on slightly modifying the engine to bring a little more power. Just going for a nice, comfortable cruiser.  The car is very straight, however i have been out of the country for 20 years and its been gathering dust at a family farm.  Will be doing quite a bit of body work to cut out some small rust areas (frnt quarter panels and a few other small bits) and fix up the paint.  Will be redoing the interior (its currently black and the seats are in real need of recovering and respringing the driver side (its front bench seat).  The dash needs a little TLC, but no real damage.  As my heater has degraded I am considering fitting something after-market that will be both heater/AC (recommendations here are always welcome). Wanting something discrete that will allow me to use the same controls and not be obvious once inside the car.   For the engine, i have been told i could consider upgrading my cam (imagine i would need a new head as well) and putting a new carby (currently the original stromberg).  However not sure what is going to be the best route.  Would certainly welcome any comments/suggestions.  As  a final step I am looking at changing the wheels. Current hubcaps are in dire need of refurbishment or replacement (imagine its a bit like hens teeth).  Thinking of some clean/classic looking mags (7-inch should be more than enough - not going for a large change in look).  Welcome any comments/advice and of course any questions. 
    • Butters
      Intercooler Choice

      By Butters · Posted

      I got the ARC M079 due to the space constraint.  Been running mint for the last 3 years.  Plazmaman also seems like a really solid choice but not used myself.    Hunt around for a better price but this is what I have - https://www.rhdjapan.com/arc-brazing-intercooler-smic-m079-bnr32.html
    • Toilet Goblin
      Intercooler Choice

      By Toilet Goblin · Posted

      Wanted to follow up on this. Did you end up getting the M073? Still deciding on what to get between nismo m073-79 and plazaman.  
    • funkymonkey
      Crank Motorsports Front Axles

      By funkymonkey · Posted

      I was just watching these boys up in QLD AWD'ing their S13 too.  
    • funkymonkey
      Returning after a long time!

      By funkymonkey · Posted

      Por que no los dos? At least my euro brawler is reliable - unlike the JDMs I've had. Sheraaz you look familiar, did you ever come to an SAU VIC meet aaaaaages ago?
×
×
  • Create New...