Jump to content
SAU Community

Big Brake Group Buy #2 - Skyline / Silvia / Stagea / Wrx / Evo / All Makes/models


Recommended Posts

I'm in for a r33 gtst front kit 356mm, street pad, anodized black, but not 100% sure yet on colour, is that alright to update later if I change my mind on colour?



Listing:
1. geetea-are - 356mm Front only / R32 GTS-t - Race Pad - Anodised Black
2. calcal - 356mm Front only / R32 GTS-t - Race Pad - Anodised Black
3.
4.
5.
6.
7.

Im not sure if it makes a difference but my car is a r32 gt-r not gts

  • 2 weeks later...

I so want in on this. I'm doing my darndest to find a spare $1800.

One question, and a long shot, I don't suppose any of these kits would fit an X series Falcon? (XA-XC and XD-XF) Also might have a mate keen on a set for a BA XR8 if any of them will fit.

Im not sure if it makes a difference but my car is a r32 gt-r not gts

Updated! :)

After thinking a bit more, i am going to pull out of this, as i think its overkill for my setup.

Ok updated.

I so want in on this. I'm doing my darndest to find a spare $1800.

One question, and a long shot, I don't suppose any of these kits would fit an X series Falcon? (XA-XC and XD-XF) Also might have a mate keen on a set for a BA XR8 if any of them will fit.

Only what is on their website is what they have kits for. So it would need to have a new dogleg made up to mount it (and ensure you get the right kit to suit the PCD) and you should then be fine!

will the 356mm Fronts fit on LMGT1 17 inch?

All 356mm kits require 18" wheels mate.

  • 2 weeks later...

Are D2's any different to ATTKD brake kits?

Also, I have a set of Nismo braided lines, would they be compatible with these brakes? Race pads and rotors are easy to source correct?

And is this group buy at risk of not happening due to numbers?

Cheers

Same stuff essentially.

As the mounting of the kit actually comes with a new arm - they might be ok (just depends on how much spare length you have).

Rotors can be sourced via Import Monster moving forward, and are cheap :)

It'll happen - just needs interest. First one is just about done

G'day Nismoid can u pls put me down for the following setup, cheers:

- Anodized Black 356mm Fronts with Race Pads for an R34 GT-T on the Gold Coast

Also, do you know of & recommend any brake specialist to install these kits around the Goldie &/or Brisbane areas???

Thanks again!

Edited by LoNg_ShaNks
  • 2 weeks later...

Looks like ill be selling my front and rear brake set and it wont clear my deep dish rims

356mm Front / R32 GT-R - Street Pad - Anodized Black

330mm Rear / R32 GT-R - Street Pad - Anodized Black

pickup only in western sydney, pm me

  • 2 weeks later...

What sort of time are we looking at for the next round? I would like a purple set for a 32gtr 356mm front and 330 rear with street pads and the handbrake kit to cairns

  • 11 months later...
  • 1 month later...

Definitely, though our pricing has reduced quite a bit anyway due to the stronger AUD since we originally conducted this GB

  • 4 weeks later...

Awesome id be keen on a 356mm front set in black for 33 gts-t. How far off before starting over again aaron?

I'm good to go whenever, not sure if the rules allow me as a business trader to conduct the group buy myself and I know that Ash has far too much on his plate right now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...