Jump to content
SAU Community

Recommended Posts

Just wondering how long it takes your car to reach normal operating temp from a cold start under normal (no lead foot) drive?

I've got a stock as a rock R34 GTT apart from an apexi pod...it takes under 60 secs to reach the half way mark on my engine temp gauge. Using Cusco 5w 40 oil.

Cheers

It should probably take a little bit longer than that, but these hot days may be causing it to come up to temp a bit quicker. I'm assuming that is while you are driving? In which case how you drive will also play a part.

If that is 60 seconds of idling then unless it is super hot where you are, that is a little bit on the quick side as it takes longer when idling.

I should add that it may just be that the gauge is just a little bit happy and there is nothing wrong with the cooling system. The gauge gets to the normal point from about 65 degrees and above

yeah mine takes not long at all really. driving at suburban speeds maybe about 2mins and its up to temp or if i start it up and jump straight onto the open road (100kph) it comes up real quick yeah maybe 60 seconds

Before with my almost dead thermostat, it would take 20+ mins.

But after swapping over to a new one, it'll take roughly around 2-3kms @ 60km/h.

As mad082 said, it really depends on the weather as well. If it's a really hot day, then the thermostat will open a lot sooner versus a cold night where it'll stay closed for longer so the engine can warm up properly.

Thats only coolant, temperature,

+1, so you shouldnt use that as an indicator that its ready to be driven hard. You want the oil temp to be normal before you do that, and it takes a lot longer.

i must have somthing wrong then, according to the power fc, im at approx 50degrees within 5min. living on acreage it can take that long to get out the front gate with a toddler getting his seatbelt on, lol, then after 5-10min at 60-80k/hr im upto high 70's,

do you guys recommend a standard thermostat or aftermarket? and what coolant temp is considered the normal?

Edited by AngryRBGTX

82 degrees is normal. and definitely go standard. go genuine nissan. you can buy plenty of aftermarket ones with lower temps, but they are a waste of time and money, partly because they will make you use more fuel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How much have you lowered?  I had 350Z springs in the rear and was able to pull the camber into factory spec with the factory arms on the rear, obviously the front ran negative camber as it isn't adjustable, but rotating the wheels regularly evened out the wear.
    • Either the installer needs to come back, you need an auto electrician, or you need to learn automotive electricals yourself.   First step Id look at is where that big thing came out of, is there still things unplugged at that location? Maybe they just forgot to put a relay in or something?
    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
×
×
  • Create New...