Jump to content
SAU Community

First Time Down The Strip.

legzy86

By legzy86,
in Motorsport Discussion & Builds

 Share

Recommended Posts

legzy86 Enthusiast

legzy86

Posted
Posted

Hey fellas just thought I would post up my stats and my first outings results.

So Ive just had the engine built in my 32 GTR, pistons, rods, nitto oil pump, poncams, 2860-5s, plug in ViPec blah blah. Anyway we only had time to tune it 15psi and spun out 300kw. Still a very basic tune and haven't touched cam timing yet. Anyway last wed night i dragged the car down to WSID in hopes of cracking into the 11s. First pass went 11.55 at 120, 2nd pass went 11.65 at 120 ( bogged it on the start) and the final pass I let all tyres down to 25psi and reeled off 11.35 at 121.79 with a 1.7 60ft. Wheel spun the whole of first so still some in it as is. In 2 weeks it goes back to rape it for what its worth on pump then doing a tune on C16. Will be interesting to see what its got in it with a full tune.

Link to comment
https://www.sau.com.au/forums/topic/418123-first-time-down-the-strip/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      You can get them with the worm drive rotator but I was too tight to pay another $250-$300 so manual labour it is! I don't think it will be too hard to rotate though. 
    • MBS206
      Left & Right Window Regulators for 2013 Skyline V36 Coupe

      By MBS206 · Posted

      Sag as in the windows start to slowly open themselves, or they're just slow to go up/down with engine off?
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      It looks like it needs a big worm gear drive on it to control the rotating, not a few sloppy pins!
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      As Duncan said, first there was OBD, which few cars used, then came OBD2.   Now an interesting point, OBD2 isn't even for what you want to do. OBD2 is for emissions testing. There is some sensor data on OBD2, but it's up to the manufacturer what they're putting on it. Most scan tools operate on UDS, which like OBD2 is a standard built on-top of CAN. UDS specifies how to structure a message, what very limited things mean such as "read memory address" but it does not specify what is stored in which memory address, that is all up to the manufacturer. You either a scan tool compatible with that vehicle, or to know how to reverse engineer all the data, which can take a VERY long time and a lot of vehicles to get it right. Oh and then the manufacturer does a firmware update and changes what's where... Ask me how I know that as fact Oh, and by the time you've got the scan tool that supports all the manufacturers stuff, well, you're back at "But a consult cable and the Nissan software" The main difference being most manufacturers software these days works with the same hardware readers, as the readers are built to support J2534 which is another standard for how the PC communicates with the tool to make it do specific things on the car...
×
×
  • Create New...