Jump to content
SAU Community

Recommended Posts

So today i parked my car in the usual spot at work and did not move it for 9ish hours. I got in my car this afternoon to move it around the back of my work (as i'm storing it in the workshop because we're getting a f*ck load of rain/flood) and all of a sudden my revs drop from 2k to 0 and the car stalls. I naturally thought "What the f*ck?" then i started the car again, drive 10 metres then it cuts again. So now i'm starting to get worried.. started the car again and drove another 15m into the workshop then turned it off.

When i first lost revs i also got a few lights come up from what i remember it was battery and a few others. Popped the bonnet and had a look around checked the belts to see if they were very loose but they were tight and everything else seemed ok. I am really not sure what's happened, we have got a hell of a lot of rain up here in the last 48 hours i'm just wondering if my car has just died because it's been driven 20m in the last 2 days and hasn't warmed up at all since it's been left in the cold the whole time.

Any feedback would be good, hopefully i get in it tomorrow and it starts fine and i have no problems.

Link to comment
https://www.sau.com.au/forums/topic/418485-strange-experience-today/
Share on other sites

id guess its fuel or air related - something to do with the fuel pump or your intake.

just some ideas:

that stalling sounds very similar to when the fuel pump has no power, it doesnt pressurise the injection manifold, the manifold has enough fuel in there to start and run for a while then eventually dies. but then you shouldnt be able to restart the car afterwards.... which would indicate a possible faulty pump. (or no fuel in the tank)

Or if your MAF sensor plug was disconnected, similar result...

or an inlet leak of some kind could do that.

i'd check the CAI hasnt popped off somewhere between the MAF and the plenum, or maybe a hose connected to the plenum (EGR or crankcase breather)

worst comes to worst, plugging a scantool up should give you a better idea

it will be a crank angle sensor or one of the cam shaft sensors. get it to a diag tool and it will give you the code, then look it up on google it will tell you what sensor it is. happened to me and it was my camshaft left hand side. about a $300 fix all up

I had a similar issue to this a while back, went to take off from the lights a few times then BAM! Felt like the engine died, hazards went on... fail. I checked a few things similar to what was suggested, disconnected the battery, reconnected, seemed to work fine after that :S Not sure if it was 100% the same however.

I would look at the cam/crank sensor too.. a failed fuel pump or air leak will generally cause it to stumble and run horrible for a bit before it stalls.. Check the codes.. it should have stored something if it is a failed Crank/Cam sensor.

Ok so i checked the MAF and intake this morning when i got to work and it all seems tight, started it up and let it get warm. Drove it around same as i did yesterday and had no problems at all. So i guess it's all sweet, if i have the problem again i'll get a scan tool on it.

Thanks for the advice

I think the engine light came on, to be honest i just thought to myself ahhh shit then tried starting the car again i didn't take note of exactly which lights came on. Yes Tony i used the clutch appropriately haha, thanks mate it's fine up here now haven't had rain since yesterday afternoon it's nice and sunny now with a bit of cloud so i reckon it's gone further south. My boss was blocked in this morning had trees down over his driveway and smashed windows from the wind.. got pretty crazy out where he is.

I have a set of Camshaft sensors, ordered from the US last may but took an age to get here and needed the car working to hit the snow fields so took it to Nissan Artarmon and had them replace the fault sensor at nissan pricing.

think they cost around $70 each ill have to double check, but cheaper than from Nissan direct

Cheers

James

Hey James, for future reference which shop did you buy the cam sensors from? Did a bit of a search on the net and couldn't seem to find anywhere. By the way, i drove the car home after work and had no problems at all. Really is a mystery as to what happened, i still think somehow it's because of the cold over the last 3 days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...