Jump to content
SAU Community

Recommended Posts

  • Replies 192
  • Created
  • Last Reply

Top Posters In This Topic

my point being, the more rules there are the harder it is to judge this stuff.....especially with novice comps.

It's hard enough to judge when everyone is in one place, let alone sending in videos etc.

The simpler the better, and the more people will do it, and the more fun it will be, because these after all are only about fun.

But hey, your challenge your rules

my point being, the more rules there are the harder it is to judge this stuff.....especially with novice comps.

It's hard enough to judge when everyone is in one place, let alone sending in videos etc.

The simpler the better, and the more people will do it, and the more fun it will be, because these after all are only about fun.

But hey, your challenge your rules

You make a good point. Maybe the next challenge can try and embody this more.

I think Simon is right, hence why were on the second page and no one has posted a vid yet

Good challenge by the way

Note: No way of telling if someone has used chalk, plus chalk is for safety, I make sure all my clients use it.

No one really special at PTC at these, Jesse (68kg) and Bender (68kg) have done 30, Martin would be close

Nina has done 16

We always do our chins this way, if hands were turned around no one here would get 10, we all find this way much, much easier

Video is the only way we'll know! Deadlifting is one thing with no vids, but it's very easy to inadvertently cheat / screw up the form with pull ups, so vids are a must.

Will take a vid this week :)

Video is the only way we'll know! Deadlifting is one thing with no vids, but it's very easy to inadvertently cheat / screw up the form with pull ups, so vids are a must.

No doubt.

I'll get a video but wanted to try it first! Its a lot harder when having to think about ensuring going all the way down, not pausing blah blah blah. Just read the rules again... "each rep is to come to a complete stop at the bottom"...hhmmmm gotta check that one....

Yeah, makes a huge difference! When I do pullups, which is rare...I do them with the pause at the bottom and I'm wrecked much quicker than on bodyweight lat pulldown, where I rarely let my arms go straight.

No. Try taking more suppliments.

lol'd

GNC Pull Up Xtend should help with this challenge...from what I read on the internet, it's designed to specifically target the lateral muscles.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
×
×
  • Create New...