Jump to content
SAU Community

Toshi Planing To Go To Brisbane In March

Toshi

By Toshi,
in General Automotive Discussion

 Share

Recommended Posts

Carbon 34 Grand Master

Carbon 34

Posted
Posted

Toshi planing to go to Brisbane in March.

Anybody interested in Toshi's road tune (also dyno tune)?

All Nissans include bolton turbo NISTUNE , remap ECU ,Power Fc ,HKS FCON

How to tune on road

I will fit wideband air fuel ratio meter(same dyno machine O2 sensor), and lap top computer, Gizzmo KMon Knock Monitor & Analysisor,before we leave.

While the customer is driving,I will sit in the passenger seat with my laptop.

Start with 2nd gear, winding up from 2000rpm-5000rpm to check car condition and datalog.I will make fuel and timing map then 2nd gear again to check air fuel ratio and engine knock.After making rough map on 2nd gear, we will go to freeway .With 3rd gear, we will be running on freeway from 2000rpm-3000rpm to check engine response and engine knock.Then next 3000rpm-4000rpm ,this will be repeated in increments of 1000rpm.If we find flat spot , slow response , laggy,engine knock etc I will fix and tune on freeway.

After I will drive myself for check and tune power and engine response.

If you would like to tune on dyno at 4th gear we go to dyno shop.

Take around 5-8hours.

Price $550 labur.

If you would like to road tune and dyno tune both , 1 hour dyno fee will not be included in the cost.

e-mail j-tech@tpg.com.au

Ph 0410490049

Not to hassle you but this sounds like a biz ad?

SAU rules !!

And last time I checked 3-4000 or more rpm in 3rd exceeds the speed limits in any state ??

Even near 7,000 in 2nd will hit 110 !!

Cowboy1600 Grand Master

Cowboy1600

Posted
Posted (edited)

Not to hassle you but this sounds like a biz ad?

SAU rules !!

And last time I checked 3-4000 or more rpm in 3rd exceeds the speed limits in any state ??

Even near 7,000 in 2nd will hit 110 !!

How can you get to > 3,500 posts and not know to check under someone's details for the "Business Trader" label?

pGAdRrJ.jpg

Not to mention having no idea about Toshi or his road tuning....

Edited by Cowboy1600
Carbon 34 Grand Master

Carbon 34

Posted
Posted (edited)

How can you get to > 3,500 posts and not know to check under someone's details for the "Business Trader" label?

pGAdRrJ.jpg

Not to mention having no idea about Toshi or his road tuning....

Maybe its because

Iturd products dont show biz labels !!

Its still not a biz trader section!!! If all traders did that it would be a mess

nor do i care about his methods of tuning they have good merit and sound practice besides just pointing out the facts how fast he plans on taking a car on public roads !!

So ge off your hi horse

Edited by Carbon 34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      High temp brake fluid?

      By Komdotkom · Posted

      Reasonably hard, although I haven't run it with the new Endless setup yet. The old brakes were F50's on 335mm rotors and the car did a 1:40.6 at Phillip Island which is a reasonable time, I'm seeing high 600s on the temperature paint. A guy I know ran the Endless fluid at WTAC without issues and he was doing 1:33's I think (Evo) with a 355/332 setup. I don't get out to the track as much as I'd like but we put the car on the hoist and spanner check every bolt and re-paint mark everything, bleed the brakes, change the fuel, check the coolant system and re-bleed blah blah blah before every event. Motorsport is expensive, RB's are expensive so a couple of hours before an event is time well spent. It's also a net time saving because if you can keep your RB from self destructing it saves you time in the long term!
    • Duncan
      First/Second Post

      By Duncan · Posted

      Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • svenskalice
      First/Second Post

      By svenskalice · Posted

      Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • svenskalice
      Kaizo Industries

      By svenskalice · Posted

      Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • believer
      HKS Vcam Step Pro Issues

      By believer · Posted

      I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
×
×
  • Create New...