Jump to content
SAU Community

Recommended Posts

There has been heaps of these threads lately which should help you out, but contact HyperGear for a simple replacement.

Dont bother changing the turbo unless you do all the supporting mods to go with it, a turbo with a stock setup will do you no favours

Link to comment
https://www.sau.com.au/forums/topic/419767-wtb-turbo/#findComment-6747266
Share on other sites

Sorry mate just a bit new to the site, started the account ages ago but only just started to use it..

In my r34 I've got

HKS FMIC

HKS 3" stainless turbo back exhaust

VDO 650cc injectors

Walbro Pump 400 LPH

Eboost street boost controller

And starting to organize a nismo type 4 board chip. That stuff is ok to start looking at another turbo isn't it? Also I want to get a wastegate but unsure on what to get? So any advice would be great!

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/419767-wtb-turbo/#findComment-6747331
Share on other sites

Yes you have some basics, i assume you mean the NIStune board which is good value for money..... If you want an easy bolt on kit look here - http://www.skylinesaustralia.com/forums/topic/261613-hypergear-hiflow-service-continued/

Link to comment
https://www.sau.com.au/forums/topic/419767-wtb-turbo/#findComment-6747342
Share on other sites

yea thanks! haha yea i meant Nistune, thought it sounded weird when i said nismo board chip in my head haha.

based in lakes entrance which is about 4 hours away from melbourne.

yea someone told me Chasers i think for a tuner?

Link to comment
https://www.sau.com.au/forums/topic/419767-wtb-turbo/#findComment-6747396
Share on other sites

Havent heard of them, jump in the VIC section and ask the locals? I am from NSW so wont be much use to you in that department :)

Link to comment
https://www.sau.com.au/forums/topic/419767-wtb-turbo/#findComment-6747411
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...