Jump to content
SAU Community

Bits N Pieces=R33 Gtst, R31, Rb30, 100Mm Cooler

SLY-25T
 Share

Recommended Posts

SLY-25T Mentor

SLY-25T

Posted
Posted

Hey All,

So I was gonna go down 25/30 route with the 33 but have decided I'd rather save to buy a house then spend my deposit on the car.

I only purchased the motor and cooler around 6 months ago and since then they have been sitting in my garage awaiting some love and attention.

All items are located in Wattle Grove, Sydney. Near Liverpool. Best contact is mobile SMS- 0401613535.

Not delivering at this time as I honestly CBF and just want it gone without hassles. Cash pickup much preffered.

1. RB30 Head and Block. Out of a R31 as can be seen by NISSAN stamps not HOLDEN. Unknown KM, only bought it to get sent away and get the works done.

$200

post-53838-0-79217500-1361235691_thumb.png post-53838-0-19006200-1361235711_thumb.pngpost-53838-0-00428100-1361235725_thumb.png

2. 600x300x100mm Intercooler with piping to suit Forward facing plenum with high mount on an RB30. Has attachment for water/meth (previous owner explained). Think the piping is to suit MAFLESS too.

$200

post-53838-0-91244900-1361236032_thumb.png post-53838-0-06324200-1361236065_thumb.png

3. RB30 Intake and Exhaust Manifolds. As previously stated, NISSAN not HOLDEN. As far as i know all the hoses are there on the intake. Only thing that should be needed is new gaskets? If I have no interest they will just be binned.

$50 for both?

post-53838-0-97340800-1361236208_thumb.png post-53838-0-14371600-1361236223_thumb.png post-53838-0-15401100-1361236235_thumb.png

4. R33 GTST HICAS unit. Was working in my car, replaced with a lockbar. As above, if no interest I'll just be throwing it out.

$50

post-53838-0-05217200-1361236356_thumb.png

5. RB25DET S1 Coil Pack cover. Prob good if you wanna muck around painting or cutting and customising.

$20

post-53838-0-14296700-1361236456_thumb.png

6. R33 GTST S1 rear strut brace. Just Jap brand. Looks to be a lil twisted but i was still able to fit it. Had alot of fuel pump issues so had enough of constantly having to take it off and back on.

$30

post-53838-0-31200000-1361236564_thumb.png

7. Excedy Heavy Duty clutch to suit R33 GTST S1 (Push?) worn out. Suit rebuild, was looking at sending away to rebuild but a clutch came up cheap.

$150?

post-53838-0-11436300-1361236675_thumb.png

As metioned, I'm not willing to post atm. Rather it get picked up and clear out my garage.

Best contact is by mobile SMS.

If most parts arent sold they will most likely be thrown out.

Throw me some offers.

Thanks,

Jaye

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Dose Pipe Sutututu · Posted

      Nice modern Hypergear high flow would be perfect.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
    • Duncan
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Duncan · Posted

      300hp (225kw) is barely outside the standard turbo's range with a bit of extra boost in it (200ish). If you are going to change the turbo you should aim for 250-300kw (330-400hp) to make the expense worthwhile
    • Murray_Calavera
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Murray_Calavera · Posted

      A couple of things, firstly omg that turbo is expensive! $3,000 USD for dinosaur technology is robbery. You could buy a G series turbo and have a good amount of change instead.  If you want a good budget option, have a look here - https://hypergearturbos.com/product/rb25dethighflow/ If you are keen to spend more, have look at the modern turbos, Garrett G series, Borgwarner EFR, etc. Have a look at the RB25 dyno results thread for inspiration.  If you upgrade your turbo to something that will support the 300hp you want and only "probably" have Haltech ECU, your car will only "probably" run. Actually, no it won't run. You are going to need the ECU and injectors at the time you do the turbo upgrade.  No thoughts on "this much boost" as you didn't say how much boost that actually is. Having said that, plenty of unopened RB25's making even more power then what you are chasing.   
    • jacobzking
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By jacobzking · Posted

      I'm looking for a direct bolt on turbo upgrade for my 93 R33 GTST.  Anyone have experience with this Greddy T620Z turbo upgrade? I'd like to be able to run about 300hp to the rear wheels without putting too much strain on the turbo. I do daily drive the car.  Pretty stock car with basic bolt ons (exhaust outlet, down pipe, high flow cat and catback exhaust along with intake and FMIC).  I'l probably have a Haltech plug n play on the car before installing the turbo. https://www.greddy.com/products/turbo-upgrade-ecr33-er34-t620z-rb25-11520057   Also, any thought on this much boost on a 30 year old motor with 250,000KMs?  Engine feels/sounds strong for what it's worth.   Thanks you in advance!
×
×
  • Create New...