Jump to content
SAU Community

Recommended Posts

I am selling my 180sx with a whole lot of mods:

Mods are:

* LSD

* BC Coilovers (all 4 with adjustable heigh and damper)

* Front and rear strut braces.

* Rebuilt SR20det redtop engine - ACL bearings - Forged pistons, rods and rings - Metal gasket kit - Tomei adjustable cams - Reseated valves - t28 low mount turbo - Front Mount Intercooler (with polished 3inch piping) - Dual stage bof - nismo 550cc injectors - 750hp fuel pump - Rising fuel rate reg - SR20 computer with nistune (running 13psi) - oil + boost pressure gauges - nardi drift steering wheel - relocated radiator overflow bottle with thermo - PIL oil catch can and all new lines that are either braided or blue silicone. - Relocated oil filter. - Cold air intake running up to a K+N pod filter. - Drift style mechanical handbrake.

It has been painted in a light blue bottom half with a slight gold pearl, with the bonnet and roof painted black.

I have been told by the previous owner that this car has been built to easily handle 20psi and reached 355hp on the dyno on 20psi. I have owned this car for around 4 months, but i am looking to sell it and another car to move into something bigger and newer. 180 has been set up for the track and drift, but has never seen either yet, i have only driven on a weekend basis and havent had any problems.

I havent done any of this work, so i dont have any receipts for the work done, only the word of the previous owner.

I dont want any joy riders or test pilots, test drives only when i see you have the cash. NOT looking for any swaps for anything!!

Photos wont upload at the moment, so please call or message me anytime on 0402 493 150 .. and i am looking for offers around $14,000

post-101149-0-82447000-1362382633_thumb.jpg

post-101149-0-64563900-1362382635_thumb.jpg

Edited by famous33
  • 3 weeks later...

any offers??

would like this gone as it just sits in my garage taking up room, and it should be getting driven !!

no reasonable offers considered

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi    have purchased pair of eibach wheel spacer as I couldn’t fit set of wheels I bought for my car due to it catching caliper.   I know I need to cut the bolts on my discs so they sit flush with the nut supplied but the nut doesn’t sit all the way into the groove meaning wheel would not directly fit onto the spacer rather the nuts. Any thoughts?   See pic   https://ibb.co/VJK5w5G
    • Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!
    • Been needing a new clutch for a while, but holding off because of life tingz and adulting. But... Being of Asian descent, I can't pass on a good sale, especially everyone else is selling it for $2k+ (JJR has it for $1799). Really on the fence on this one, because the unsprung version of this is $1281 via Shitbox (Sparesbox) and the sprung version is quite a bit more (no idea why Shitbox doesn't offer them). Ending up just sending it and getting the twin sprung organic. Mainly because I wanted the car to be nice to drive and didn't want to make it more of a shitbox than it already is.    
    • It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?
    • yep just a JIC vs ISO insulator height. old coils are for JIC, new coils are for ISO
×
×
  • Create New...