Jump to content
SAU Community

Recommended Posts

I bought a set of ID2000's for my GTR, but seem to be having a bit of a drama with fitting them... The inner diameter (side that slots into manifold) seems too large at 13mm to actually fit. What size are they meant to be?

Am i missing some type of adaptor that reduces the 13mm injector body to something like an 11mm tip to slot into manifold, or have i been supplied the wrong injectors??

Link to comment
https://www.sau.com.au/forums/topic/421076-injector-sizing-gtr/
Share on other sites

Anyone that confirm the above 100%?

My plenum looks as though it may have some type of sleeve in the opening, but upon closer inspection (plenum still on car) it appeared that they were a part of the original casting... Not so sure now??

Pic attached for reference.

0426F605-698C-4B1C-B2A0-5A7BCE96A5E7-186

As far as I'm aware, the injector sits hard up against that port, and is held their by the pressure of bolting down the rail.

The Id2ks don't go inside that port like a factory or jap brand injector.

Correct me if I'm wrong

The O-ring doesn't make contact with the manifold as the tip of the injector is too wide to even fit in a few mm, so i didn't think it was right. Pressure would just hold the plastic end cap down to that cast flat section, negating the need for an O-ring even, but would leak under pressure afaik??

Would love to hear from someone that has fitted a set of ID2000's to a standard plenum GTR!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • People think it's a waste of space, ugly, etc, generally associate "emissions control equipment" with "bad". These OBD1 vacuum-only systems I'm not a huge fan because I think they don't go far enough. They're wasting some of the fuel captured because they start purging as soon as the engine pulls vacuum. Later OBD1/OBD2 they put an electric purge valve on them to vent only when closed loop is active so the ECU will trim some fuel out. Even later OBD2 with zero evaporative loss the tank is 100% sealed from atmosphere until you run the engine or press the refuel door release. The tank has to take much higher vacuum/pressure spec but you never deal with saturating the charcoal canister and losing some fuel that way. The fuel also lasts as long as it would in a 100% airtight container which is nice when you're dealing with modern E10 pump gas.
    • If your luck is anything like mine, what happens is in the process of pulling hoses to get access to the one leak you create many more leaks because every o-ring was on the verge of failing and the strain of pulling it apart caused it to fail. Sometimes life is simple, sometimes you pay twice trying to save once. For the R33 you can still get most AC components from Nissan, I use nissan epc data or amayama to look up the part numbers and then search for the cheapest/most practical way of sourcing from there.
    • The dirty secret is there is nothing recyclable about the plastic bag or old plastic bottles either. Our local trash collection explicitly calls it out as hazmat in both cases. Oil-soaked rags + paper towels too. Oil-soaked cardboard is also not recyclable. The most common case of oil-soaked paper like that is pizza boxes, which are explicitly compost-only from the oil. To my knowledge hazmat oil contaminated plastic the only solution is either landfill or "thermal recycling". Most plastics in my experience there is slow permeation of the oil it's holding into the container so it's very challenging to get it 100% clean.
    • Yes, and since RAA insurance essentially being swallowed up by the same monster that is NRMA insurance and all those other clowns, they are no bloody good now either. We dropped RAA insurance for the house a little while back because they lost the plot.
    • I can tell you now, good luck if you're with NRMA (NSW equiv of vis RACV and QLD RACQ). Because NRMA are freaking horrendous to deal with for claims, even with a normal road car. Not to mention even more BS when they're in the wrong and didn't cancel a policy etc when they were meant to and make you jump through hoops for things.
×
×
  • Create New...