Jump to content
SAU Community

Bonnet Hinge - Rubbing Issue

Seano350GT
 Share

Recommended Posts

Seano350GT Veteran

Seano350GT

Posted
Posted (edited)

Since the day i picked up my car i have had this issue with the bonnet rubbing with the fender and i am finally getting around to fixing it up..

The cause of this rubbing is the hinge itself, somehow it's bent causing this to happen..

Here's a picture of what the bonnet corner/fender looks like after 12 months of rubbing.

foq6up.jpg

ioeykk.jpg

It's not noticeable until you get up close, then it looks horrible. I have tried putting washers behind the bolt holding the hinge in to give the bonnet a bit of height but i can't seem to get it to line up with the fender without it rubbing and it looks silly having it too high.

Now, what my problem seems to be is sourcing a new bonnet hinge. I have been in contact with my buddy Charles from B2Autodesigns in the states but he thinks the guys at OCinfiniti reckon they are different. It's hard to tell between pictures without having the hinge off the actual car but here's a pic of it on my car compared to what i found on google for a g35 hinge.

1zbf288.jpg

64ie6q.jpg

I would go ahead and order a new set of hinges and pay $100 but i'd rather make sure they will actually fit the car. I also plan to get the corner touched up once i've replaced the hinges as it looks horrible and i hate it :/

My local Nissan could be an option, but my experience with those guys has been nothing but negative. Ever since the head service manager told me i need to take the car to a panel beater to get a compression rod bush replaced...

If anyone could shed some light on this that'd be great,

cheers

Edited by Seano350GT
Link to comment
https://www.sau.com.au/forums/topic/421226-bonnet-hinge-rubbing-issue/
Share on other sites
gillywig2 Rookie

gillywig2

Posted
Posted

I'm going to be ordering a pair of hinges from Perry Infiniti soon. I can't see why they would be any different to the G35 hinges.

It's a very common problem as highlighted on http://g35driver.com/forums/interior-exterior/216502-another-hood-hinge-bending-problem.html

Seano350GT Veteran

Seano350GT

Posted
  • Author
Posted

Andy, thanks heaps for that link i didn't realise how common this issue was. First time i saw it i thought to myself "shit it's been in an accident" lol.

I don't see why they'd be different either, it just seems to look like they are judging by the pictures. Not sure if i should go ahead and buy the hinges from the U.S yet. I might give Nissan a ring today and see if they can help but i highly doubt it.

Seano350GT Veteran

Seano350GT

Posted
  • Author
Posted

Amazingly enough, Nissan came through. Must be a new bloke that works at my local Nissan because he's the first one to actually know what a V35 is lol.

$65 for a set of hinges coming from Melbourne so that's good news. My next issue is apparently you have to remove the fender to get the hinges undone.. that sounds like fun.

Seano350GT Veteran

Seano350GT

Posted
  • Author
Posted

turns out it's actually a really common problem with the hinges starting to bend.. quite weird if you ask me. But yeah i need to see if it can be done without removing the fenders, after some reading on g35driver.com it seems the fender has to come off. But in saying that a bunch of people were also commenting saying no you don't have to take it off.. we'll see lol.

junkie Mentor

junkie

Posted
Posted (edited)

reminds me on a grandpa's lancer i worked on once, bonnet was hard to open, turns out both hinges were rusted solid. i was actually bending them when opening and closing the bonnet, and the passenger side was already becoming soft and ready to snap

Edited by junkie
junkie Mentor

junkie

Posted
Posted

had a good look at mine today. seems like the longer part of the hinge, between the pivot point and the bonnet, has some flex in it, you can actually spot it when opening the bonnet

with that amount of flex, if the pivot point isnt lubricated properly, it would flex enough to catch the corner of the guard, and only on the way up

the pivot point itself appears to be in an area with a bit of water runoff from the a-pillar area, so regular lubrication would be a good idea

you can reach it with a thin tube between the a-pillar/guard and lower windscreen trim panel, there is just enough gap there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
    • kevboost7
      Magnetic Drain Plug Snapped in Half

      By kevboost7 · Posted

      F my life. I was changing the oil on my R32 GTR today as usual and ran into a bit of a snag. I drained the oil out and was getting ready to finish the job by tightening the drain plug, however The stupid magnetic oil drain plug snapped in half, right at the magnet part. After about an hour of trying to remove it, I used a drill bit, which unfortunately pushed the magnet all the way into the pan, and just leaving the hollow threaded part of the bolt remaining. I was able to remove the hollow portion of the bolt from the oil pan with some pliers but the magnet is still in there.  So, the question is, should I drop the oil pan to get the magnet piece out, or is it okay to leave it in there? I really dont want to drop the pan, i'm about to go nuts.  PSA: Do NOT buy a BLOX magnetic drain plug. This is the one i had.    https://bloxracing.com/products/magnetic-oil-drain-plug-m12x1-25mm?variant=37131252859052&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gad_source=1&gclid=CjwKCAjw47i_BhBTEiwAaJfPpgti1D2JwO7TDuMpXuqeQPCuIQSAfwxpWQH5rF9MD7sm5SCZDWLR_RoC_YoQAvD_BwE    
×
×
  • Create New...