Jump to content
SAU Community

Recommended Posts

Sierra stage 1 turbo

Scotty dump

Scotty 3" front pipe

Nismo exhaust

Plenum spacer

Scotty actuator mod

Hdi front mount

Transgo shift kit

Turbosmart boost t

I do have a nismo ecu but it isn't fitted as it was running to rich. It will be waiting till I have money to do my emanage

Think thats it haha

sh###t you be running 13eents easy, while i hope for a 14 flat

my mods

dump pipe

custom 3" exaust

shift kit

custom intake pipe

14.1 with these mods 1.9 60 foot

I'm really hoping so. I need a new BOV so hoping that doesn't effect me to much, its bleeding off a bit up high. Also really need an intake pipe to get the most out of my setup. But we will see how we go.

Well not exactly what I had hoped for, 14.02 @161km/h I hit boost cut twice on tgis run. So it should have been a 13 easy. I had boost wound down as low as possible so not sure what to do next. Every other run hit cut a bunch more times so was much slower.

  • 2 weeks later...

Took the car to Hiddenvalley last night, managed a 13.6 at 102 so still doing the same mph, couldn't get my 60 foot under a 2 seconds, very very slippery! They just had scrapped the rubber of and re layed vht hopefully when they get more rubber down it will be better! Plus side I've managed to get my reaction down to .006 so managed to do a number of .406 reactions

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
    • F my life. I was changing the oil on my R32 GTR today as usual and ran into a bit of a snag. I drained the oil out and was getting ready to finish the job by tightening the drain plug, however The stupid magnetic oil drain plug snapped in half, right at the magnet part. After about an hour of trying to remove it, I used a drill bit, which unfortunately pushed the magnet all the way into the pan, and just leaving the hollow threaded part of the bolt remaining. I was able to remove the hollow portion of the bolt from the oil pan with some pliers but the magnet is still in there.  So, the question is, should I drop the oil pan to get the magnet piece out, or is it okay to leave it in there? I really dont want to drop the pan, i'm about to go nuts.  PSA: Do NOT buy a BLOX magnetic drain plug. This is the one i had.    https://bloxracing.com/products/magnetic-oil-drain-plug-m12x1-25mm?variant=37131252859052&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gad_source=1&gclid=CjwKCAjw47i_BhBTEiwAaJfPpgti1D2JwO7TDuMpXuqeQPCuIQSAfwxpWQH5rF9MD7sm5SCZDWLR_RoC_YoQAvD_BwE    
    • I actually have an aftermarket hanger, the detschwerks x1 hanger, but my dw420 has never really sat in it correctly, good to know I can just modify it a bit to suit. Yeah cheers man will definitely have a play with it and hope it solves my dramas.
    • Seriously though, it's the Shaft Autoservice high mount rear spoiler: https://az-style.shop/items/5ffaad5a72eb464137a6edb1
    • That's the 'low downforce' version of this:  
×
×
  • Create New...