Jump to content
SAU Community

Recommended Posts

Hi all I'm sorry to post this as a newbie to the forum but as it happens a gum tree fell on my car and I didn't get a lot of say in it. The roof / pillars of the car took all the force so the chassis was fairly ruined, nearly everything else has remained intact. The car had ~150,000km's but many parts had been upgraded or replaced recently, car dynoed 270rwkw at last tune with no signs of issues on a GT3076

I'm negotiable on all prices within reason, If you want to make an offer on anything go ahead. I would prefer you contact me by email or a post on here then it's first come first serve, or you can call me AFTER 6pm weekdays any time weekends, email address is [email protected] phone number is 0406 404 457.

I'm happy for you or a member on here etc to come check out gear etc I have photos of pretty much every part but can't realistically put them all up, send me an email address and I'll send photos. Pickup on the bigger stuff is preferred I can post but it will be a few extra days delay in getting it boxed up and time out of work to send it off. All parts located in the ACT

Also willing to do better deals on multiple items, let me know what you are looking for on the engine in terms of accessories etc.

List as follows:

Steering and Suspension

Front upper control arms

50

Front Brake Calipers

120

Rear brake Calipers

50

Front strut brace

50

Brake Rotors

80

Pedders "Extreme" Coilovers

800

Front lower control arms

50

Power Steering Rack

80

Front castor rods

50

Rear lower control arms

50

Front 5 stud hubs

50

Rear 5 stud hubs

50

Engine Bay

Engine (Bare engine i.e.no ecu accessories etc unless requested)

1500

Wastegate Tial

250

Exhaust Manifold High mount unknown brand suit GT3076

200

Intercooler + piping (Hybrid)

300

Injectors (unsure of brand - supported 300kw without issue)

300

Turbo heat bag (poor condition)

20

Power steering pump

80

Air Con condenser

60

Alternator (1000km old)

200

Blow Off Valve Turbosmart

50

Power FC + hand Controller

950

Washer Bottle

20

Catch Can

30

Greddy Plenum

250

GT3582R turbo complete - Blown bearings

150

GT3076R Turbo housings + core (Blown bearings)

150

Exhaust Dump to tip external gate plumbed back to exhaust

400

Radiator

40

Z32 AFM

80

Drivetrain

Driveshafts

50

Differential

250

Gearbox Rebuilt with R34 internals (2000kms old)

2000

Clutch (2000kms old)

600

Flywheel (2000kms old)

300

Interior

Eboost 2

120

300km/h dash

80

Head unit + speakers (generic deck 4 inch fronts 6X9 rears)

50

Front Seats

140

Rear Seat

80

Door skins

120

Miscellaneous

Headlights

50

Battery (200kms old)

50

20 inch Zenetti Masquerade Wheels + 90% tread generic cheapish tyres

1000

LHS Mirror

40

Front bar

100

Rear bar

80

Ignition Barrel + door Locks with key (door locks match but fitted to door)

100

Boot lid

40

Passenger front Guard

50

Drivers side front Guard

50

Passenger Door

60

Drivers Door

60

S14 Spare decent tread

50

Bonnet

50

Gearbox will fit a standard R33, but has been upgraded to the higher quality R34 internals. Work was done by Jason at Autotorque in Phillip ACT clutch is a heavy duty Excedy single plate he recommended for running 270kw and the flywheel is a lightweight sports replacement. The setup is amazingly light and driveable but should be pretty reliable for decent power have receipts for something in the order of $5500.

Engine has 150,192kms, to the best of my knowledge has not been opened but was in perfect running condition when removed. Not 100% sure of the brand on the injectors, but the car was tuned to 300kw then reduced to 270 for reliability so they appear to fairly comfortably flow 270kw+ Let me know what accessories etc you would be after

post-97282-0-05630300-1363090274_thumb.jpgpost-97282-0-01567700-1363090299_thumb.jpg

Cheers

Karl

Edited by karl3
Link to comment
https://www.sau.com.au/forums/topic/421549-wrecking-modified-r33-gts-t/
Share on other sites

hey mate interested in the Eboost 2 and 300km/h dash and are the headlights s2 or s1 cnr see clearly in the pic also interesed in the plenum can u send me some pics might take the lot off u msg me a price for the lot on my phone plz 0422660086

thanx mate

Hey guys thanks for the replies, few pics attached as requested, I'll sort out a response / who got in first for various items by tonight (got a few emails etc as well)

Plenum is the one pictured, I've attached another with brand / underside. Headlights I would be assuming are S1 but I'm not an expert on the differences

post-97282-0-45565400-1363119202_thumb.jpg

post-97282-0-08282300-1363119293_thumb.jpg

post-97282-0-79728900-1363119352_thumb.jpg

post-97282-0-02886600-1363119421_thumb.jpg

Hi, Karl

Would you have the front tail shaft and I am chasing a S1 bonnet preferable in silver. I am from Melbourne

Can arrange pick up for tail shaft

cheers

Alex 0433878905

  • 1 month later...

Sorry for the slow reply guys I thought this thread had fizzled out.

DD33: I honestly have no idea, if you're local I'd be happy to take it round for a test fit

Simdog I have but am looking to sell as a whole with the gearbox at the moment, sorry

Bri73Y no worries I'll get a shipping quote and PM

Spinksy07 I'll PM you a photo

Update on what has sold so far:

All suspension except rear left hub and steering rack

Engine

PowerFC

Inlet plenum

Exhaust manifold

Injectors

Clutch

Flywheel

Wastegate

Front Calipers

AFM

GT30376R Rear housing

Boost controller

Headlights

Zenetti rims

Edited by karl3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
    • F my life. I was changing the oil on my R32 GTR today as usual and ran into a bit of a snag. I drained the oil out and was getting ready to finish the job by tightening the drain plug, however The stupid magnetic oil drain plug snapped in half, right at the magnet part. After about an hour of trying to remove it, I used a drill bit, which unfortunately pushed the magnet all the way into the pan, and just leaving the hollow threaded part of the bolt remaining. I was able to remove the hollow portion of the bolt from the oil pan with some pliers but the magnet is still in there.  So, the question is, should I drop the oil pan to get the magnet piece out, or is it okay to leave it in there? I really dont want to drop the pan, i'm about to go nuts.  PSA: Do NOT buy a BLOX magnetic drain plug. This is the one i had.    https://bloxracing.com/products/magnetic-oil-drain-plug-m12x1-25mm?variant=37131252859052&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic&gad_source=1&gclid=CjwKCAjw47i_BhBTEiwAaJfPpgti1D2JwO7TDuMpXuqeQPCuIQSAfwxpWQH5rF9MD7sm5SCZDWLR_RoC_YoQAvD_BwE    
×
×
  • Create New...