Jump to content
SAU Community

Recommended Posts

its only running 19psi in the mid , theres hardly any change to the boost at the redline, hence you get the same rwkw?

Maybe get an ebc and set it up for 19psi at redline , and add the 3inch steel intake pipe, although im not sure that turbo is happy with much more than a bar is it?

I agree there's barely much variance at the peak power in boost between the two setups.

If you focus on deresticting intake & exhaust, and get the boost steady from midrange through to redline (can be tough on internal wastegate turbos) then you should get a better result.

Or do what Jez said lol

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

What are the inlet temps with that sidemount? That 210 alone is impressive in my book for a side mount intercooler. What are the ARC sidemount's dimensions? I'm guessing decently thick but still rather small length and height wise.

that was the issue last time, AIT were sky high, now it can make that power all day.

it was odd that it would not make power even adjusted cam gears all over the place with no real gains.

Only thing i could pick was intake was rubber and small.

it is also has more mid as it took more mid timing.

that was the issue last time, AIT were sky high, now it can make that power all day.

it was odd that it would not make power even adjusted cam gears all over the place with no real gains.

Only thing i could pick was intake was rubber and small.

it is also has more mid as it took more mid timing.

This sounds more and more like restrictions. The fact that it's not responding to boost and timing.

I would do as I did, and take the advice of Status and knowledgeable SAU members and go down the well beaten path of getting the engine breathing with proven mods (intake pipe, quality front mount, quality dump pipe, good cat, free flowing cat back) before moving on to more in depth troubleshooting.

What size injectors are you using Chris?

Currently have some Nismo 555cc ones.

Yes there are some exceptions,

But imagine if u had an rb25 :)

Haha I have to imagine a world where I could afford all that first! Surely the better pump and some bigger injectors and I can still get 250!

Also what exhaust do you have? 3" all the way? Cat?

Some people don't agree but I install a decat pipe when ever I do exhaust upgrades.

I find the car seems much more rev happy with out them! Assuming the rest of your exhaust is good!

You can get silicone intake pipes for about $60 of eBay might be something to think about?

Filter is it a good brand? And clean? You would be surprised at how much hp you can loose with a dirty one!

These are the things I would check first and then play with the boost until it holds 19psi to redline

its only running 19psi in the mid , theres hardly any change to the boost at the redline, hence you get the same rwkw?

Maybe get an ebc and set it up for 19psi at redline , and add the 3inch steel intake pipe, although im not sure that turbo is happy with much more than a bar is it?

3" all the way with hiflow cat. Will buy new silicon joiners & new air filter on the way (although Trent gave a few runs with lid off to see if filter restricting)

Staying away from any ebc / bleed valve for now...

Rb20's just dont seem to be making power lately. Time for rb25 :)

once (if) the 20 pops, then a 25 will be put in :P

that was the issue last time, AIT were sky high, now it can make that power all day.

it was odd that it would not make power even adjusted cam gears all over the place with no real gains.

Only thing i could pick was intake was rubber and small.

it is also has more mid as it took more mid timing.

Will modify intake next weekend and will have to pop by for another run!

This sounds more and more like restrictions. The fact that it's not responding to boost and timing.

I would do as I did, and take the advice of Status and knowledgeable SAU members and go down the well beaten path of getting the engine breathing with proven mods (intake pipe, quality front mount, quality dump pipe, good cat, free flowing cat back) before moving on to more in depth troubleshooting.

will do. Will report back once intake is sorted out.

Thanks everyone for the help. Will keep this thread updated with any progress :)

Also have you done the throttle body coolant bypass mod?

It's very easy and can drop your intake temps but a few deg :)

It's one of my favorite mods cost nothing so free power!

Why is it run through the TB stock anyway? Is it emissions or something? I had that mod done on my rb25 180 when I had a plazmaman plenum because I had to, but I thought it must be that way stock for a good reason... :huh:

Why is it run through the TB stock anyway? Is it emissions or something? I had that mod done on my rb25 180 when I had a plazmaman plenum because I had to, but I thought it must be that way stock for a good reason... :huh:

It helps to prevent icing in the TB in cold weather. Think really cold, like Northern Japan cold. Totally unnecessary in 99% of Australia.

i made about 220wkw on rb20 with the same turbo tho it ran out off steam aswell....your not going to get anymore out of that its too small! ive also maxed a TD06 at 270wkw @ 17psi. Pumped 20psi into and picked up 50wkw in the mid range instantly but lost 2kw top end due to the turbo just not being able to flow up top

exactly what is happening here

i made about 220wkw on rb20 with the same turbo tho it ran out off steam aswell....your not going to get anymore out of that its too small! ive also maxed a TD06 at 270wkw @ 17psi. Pumped 20psi into and picked up 50wkw in the mid range instantly but lost 2kw top end due to the turbo just not being able to flow up top

exactly what is happening here

exactly and where do you spend most of your driving time...in the midrange or on the limiter....;)

Sorry for the late reply

The coolent in the throttle body is to stop it freezing when in sub zero deg temps!!

I am talking about -10 and colder!!

So it is NOT required in Australia!!

Just for example

The lowest temperature ever observed in Japan was -41 degrees Celsius (-42 degrees Fahrenheit), recorded in Asahikawa in January, 1902.

Keep in mind that the intake temps on a (street aka no ice boxers) turbocharged car are normally between 10 to 20 deg hotter than the air temp (depending on setup)

Different dynos but there are loads of people running 220-240rwkws out of a 2530. I know Russ ran 21psi through his thing and made 23#rwkws for a long time before throwing his RB25 in. He couldnt get it to hold more than something like 16psi at redline as it would not hold boost.

For giggles replace the inlet pipe, blank off BOV and remove cat for tuning and go from there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...