Jump to content
SAU Community

Recommended Posts

Licensed 1990 R32 GTR gun metal grey that I personally imported from Japan in 2005. The car is licensed and comes with 6 months WA rego and was always well maintained with Motul oils and was tuned by Hyperdrive. I decided to sell the project due to poor health.

Since owning the GTR I had done a few modifications and decided to strip the engine bay etc for a full respray when some person decided it would be a good idea to key it all over. At the moment the engine , gear box and engine bay components have been taken out ready for a respray, all interior is still in place. The body is rust free.

The engine had no issues when it was in the car and had about 160psi in all six pots.

Modifications done so far are as follows:

Engine:

  • Tomei Type B 260 cams
  • Tomei cam caps
  • Sard 700cc injectors
  • K&N pod filters and pipe work
  • Spitfire coils
  • Garret 2860-5 turbos
  • Sard Ali racing radiator
  • Sard fuel regulator
  • Full Monty clutch
  • Trust intercooler
  • New CV joints and boots
  • Bosch 044 in tank fuel pump



Brakes & Wheels


Fully rebuilt front brake callipers
Stock R32 GTR Rims
New Brake Lines
Tein Super Street Coilovers
Nismo clutch slave

Electronics

Apexi Power FC and Hand Controller
Blitz Dual solenoid EBC has LCD display
Full White Nismo Dash & centre console


Not Yet Fitted

New rubbers, badges, seals and mouldings for whole car ( Over 2.5K+ alone)
Complete engine seal and gasket kit.
Spare front seats
New silicone hose set for engine

New genuine hose set for engine
Kakimoto dual exhaust
R34 Dump pipes ( better flowing then stock R32 items) "photo not taken yet"
Tomei 2mm oil restrictor
Fully refurbished R32 gear box "photo not taken yet"
Mines Baffle kit "photo not taken yet"
Tomei sump baffle kit "photo not taken yet"
GREX oil pump

6Boost Manifold for single top mount

New Garrett Gtx3582R

Nismo engine mounts

New handles

New handle surrounds

2.8L Fardon Stroker crank ( where HKS got their cranks ) Step two crank

Apexi intake kit

Arp head and engine bolts

ATI 1000hp balancer and pulley kit

Carbon fibre rear strut

DBA 4000 rotors

FC data logit

Pauter rods

new set of tein coilovers

And anything else I missed from list.

That's all I can remember for now. Car was never tracked, taken to drags or thrashed.
Chasing for whole package is $17,000.

NO SWAPS NO TRADES NO PARTING OUT

Rob 0413 670 040 or email rfkarl@hotmail.com

post-25605-0-20721000-1363580958.jpg

post-25605-0-26953700-1363580965_thumb.jpg

post-25605-0-95457100-1363580965.jpg

post-25605-0-35765100-1363580966.jpg

post-25605-0-94447700-1363580966.jpg

post-25605-0-61396500-1363580967.jpg

post-25605-0-25812000-1363580968.jpg

post-25605-0-67544100-1363580968.jpg

post-25605-0-70361200-1363580969.jpg

post-25605-0-53092400-1363580970.jpg

post-25605-0-80544100-1363581043.jpg

post-25605-0-27797700-1363581044.jpg

post-25605-0-70706100-1363581044.jpg

post-25605-0-23036100-1363581045.jpg

post-25605-0-71883300-1363581045.jpg

post-25605-0-31011900-1363581046.jpg

post-25605-0-06429000-1363581048.jpg

post-25605-0-06877700-1363581049.jpg

post-25605-0-67133800-1363581049.jpg

post-25605-0-65716700-1363581050.jpg

post-25605-0-06956900-1363581142.jpg

post-25605-0-07699200-1363581143.jpg

post-25605-0-26692500-1363581145.jpg

post-25605-0-48562300-1363581146.jpg

post-25605-0-56830200-1363581147.jpg

post-25605-0-60579900-1363581148.jpg

post-25605-0-81894500-1363581149.jpg

post-25605-0-91344300-1363581150.jpg

post-25605-0-99766100-1363581151.jpg

post-25605-0-09902000-1363581153.jpg

post-25605-0-49748200-1363581210.jpg

post-25605-0-87492300-1363581210.jpg

post-25605-0-75364300-1363581211.jpg

post-25605-0-58014600-1363581212.jpg

post-25605-0-97435800-1363581212.jpg

post-25605-0-53195000-1363581213.jpg

post-25605-0-99473000-1363581213.jpg

post-25605-0-10782000-1363581215.jpg

post-25605-0-88166200-1363581215.jpg

post-25605-0-68186500-1363581216.jpg

post-25605-0-88014800-1363581314.jpg

post-25605-0-21993500-1363581315.jpg

post-25605-0-73827000-1363581315.jpg

post-25605-0-16258200-1363581316.jpg

post-25605-0-55888900-1363581316.jpg

post-25605-0-12232000-1363581317.jpg

post-25605-0-51609100-1363581317.jpg

post-25605-0-98197200-1363581317.jpg

post-25605-0-39342000-1363581318.jpg

post-25605-0-89881200-1363581318.jpg

post-25605-0-34652400-1363581357.jpg

post-25605-0-73246000-1363581357.jpg

post-25605-0-14937100-1363581358.jpg

post-25605-0-69046300-1363581358.jpg

post-25605-0-10314100-1363581359.jpg

post-25605-0-62224900-1363581359.jpg

post-25605-0-01875400-1363581360.jpg

post-25605-0-58515400-1363581360.jpg

post-25605-0-01743000-1363581361.jpg

post-25605-0-56445200-1363581361.jpg

post-25605-0-26678000-1363581380.jpg

Link to comment
https://www.sau.com.au/forums/topic/421870-r32-gtr-unfinished-project/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Swapped the injectors around and the misfire followed. I went ahead and ordered the Deatschwerks 550cc injectors and am currently waiting for them to be ship and arrive. In the meantime, I've had my Nistune soldered to the ECU. Tested it, and and tried it out with the software. Everything should be prepared for when the injectors arrive.  
    • Yeah they charge a little extra for mods , last year I noted no mods but I did have an exhaust fitted after that so  better to let them know cause these kinds of things can cause the policy to be void if you ever need to claim.
    • Hello, just just bought an 1999 enr34 with a stock rb25neo and I'm looking to upgrade the engine to 500whp I know some basic things but wondering if there are things I'll need to do to upgrade the stock block and all the bits and pieces to achieve this.
    • Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 馃槄
    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 馃珷    
  • Create New...