Jump to content
SAU Community

Recommended Posts

Just back from an interstate road trip, and got defected in Victoria because the muffler was 10mm too close to the ground (Highway Patrol initially stopped us because "your number plates have a black background", but then went over the car until he could find something/anything to defect).

I've had my Stagea for 3.5 years, and the coilovers (set to max. height), wheels, and exhaust (HKS 3") were unchanged since import.

To get the clearance to the minimum 100mm, I had the HKS muffler removed, and a hotdog fitted in its place. It's a little noisier from the outside, but now I've got nasty resonant vibrations inside that are making my teeth grate....

Any suggestions ? I suspect I've made a big mistake in doing the "quick fix" and destroying what was a well-tuned system. :unsure:

Link to comment
https://www.sau.com.au/forums/topic/422685-c34-stagea-exhaust-advice-please/
Share on other sites

You couldn't just get the exhaust hangers reset to bring the exhaust up closer to the underbody? If its only 10mm you should be able to do that without too much fuss.

Yeah, sorry, should have mentioned that that is what the exhaust shop tried first. The hangers were tight as, and really close to the floor. He even tried putting a stand under the muffler, heating the pipe either side, and attempting to add some extra bends, but everything was already really, really tight under there.

Wipe arse with Victorian defect notice and mail back to them?

This is not that different to what Legal Aid Victoria said, "Ignore it, and wait a couple of months until you get a letter from Roads & Maritime NSW".

Don't know about Victoria but in NZ the minimum clearance (without a cert) is 100mm to any solid part of the body or chassis and this excludes things like skirts or exhaust. Have you checked the regs for Victoria?

Hot dogs dont quiet much at all. A small Berkley straight through muffler will flow plenty, and actually quiten down the exhaust. It would fit in either mid or rear position, and they cost less than 100 bucks. Why didn't your exhaust shop just put one of them on ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From the pictures I have when doing the job the flywheel is the same diameter, I don't think they're playing weird tricks like putting weights at the outer diameter to increase flywheel inertia or anything like that. The OEM flywheel is definitely heavier, but it's not a huge difference. Quoted weight savings of the clutch is 2 kg so I can't imagine the flywheel being lighter than ~7 kg. Kind of regret not weighing it before the clutch went into the car but as far as driveability goes I have no complaints.
    • HKS trigger kit should be very easy to integrate with a Link. It's a 36-2 crank trigger. Hard part is finding the motivation to take off the timing belt and everything on the front of the engine to install it. You also need to cut out a hole in the oil pump housing so the sensor can read the trigger wheel. Changing out the cam sensor for a 24 tooth setup is probably good enough but as others have mentioned depending on what underlying assumptions are changed it becomes more of a problem. Reading the crank state off of the cam is an abstraction that works in the general case, but if you have an edge case it makes less and less sense. There is a GTX2860 gen 2 that can take a compact 5 bolt housing so it's direct bolt on but I'm not 100% sure of what's involved. Peak compressor efficiency drops off a bit on these turbos vs -5s, 77% vs 73% but you get way, way wider region of operation. The -5s have a really strange surge line in their compressor map that is all over the place. If you think the hot side on the -5s aren't open enough you can try the Tomei T550B turbos which a local tuner seems to be happy with:
    • i need a complete tail light for my R33 GTR if you have please let me know.
    • I need a great maintenance workshop around Idaho, if you know one please let me know..
    • Hello friends, i have a good friend in Canada that looking for a good condition 1993 GTR around him please if one or know someone around you that is willing to let it go please let me know so that i can inform him.....Thanks
×
×
  • Create New...