Jump to content
SAU Community

Recommended Posts

Intake done in December. I think the ping was before the intakes went in.

Even if it was after...wouldnt the ECU be picking up the different intake and adjust accordingly? I reset the ECU a couple of times since then.

Ping only at low revs...1.8k to 2.3k? higher revs/speeds no ping.

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6809879
Share on other sites

Nope, have not changed spark plugs/fuel pump at all.

Got the car Nov 2012. Car is a 2007 V36. Got it with 36k kms on the clock.

I'll try United P100 and see what happens. Will try to clean MAF and throttle body on the weekend and proceed to spark plugs and fuel pump if all fails...

Is there anything I am missing? Should I try stock air intakes?

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6809912
Share on other sites

Maybe try running some Subaru upper engine cleaner through it? Get rid of some gunk built up in there (and give you a nice clean intake manifold while you are at it - might not fix it, but for under $20 it is worth a try) My V35 ran beautifully afterwards

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6810137
Share on other sites

It also depends on where you bought it as to whether it really has 36k on the clock - it costs under $100 to get this changed. If you have more km on the clock, there are other things that could be more built up in the engine or things that could be wrong. Obviously at 36k it should be basically a brand new car ...

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6810198
Share on other sites

Ok ill try checking the AFM and the cleaner. I dump in Nulon Fuel System Cleaner and 44l of P100 last night. Lets see what happens over the next few days.

I bought the car on auction from Japan. It was checked for genuine KMs by computer system. Whether or not it's genuine, can't really be that sure but yes essentially the whole car looks brand new and nothing was modded or been touched.

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6810623
Share on other sites

Could the the timing yes, one of the more common causes...

Mine has zero mods, its just my daily and I haven't had it for long, but being a high comp engine with Japanese ecu tuning I'm not hugely surprised by the ping on crappier fuel. But I will look at spark plugs and intake clean soon

The Mirage on the other hand has been driving me nuts. I have changed the plugs, plug leads, dizzy cap, rotor, fuel filter, air filter, checked the timing, three rounds of intake cleaning (two at home and one with a pro machine) and full bench injector clean with new o rings etc... yet, still pings :rolleyes:

Next step - colder plugs and oxy sensor. No luck with cheap OBD2 adaptor either

Link to comment
https://www.sau.com.au/forums/topic/423199-ping/#findComment-6813062
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No worries, everything worked out in the end. I just wanted to make the point that it doesn't matter where it comes from (I.E Australia), it can be broken or improperly built. I would still purchase from these companies in the future. B2R - Not certain how that finished, this was on a car I wired a few things and street tuned. I know the owner ended up shipping the motor back to Australia for investigation. Hopefully some of it is covered under warranty.  Turbosmart - I always pressure test everything that goes on my car. It's a habit from my career in oil and gas. I run two 40mm's and both had major leaks from the actuator to exhaust portion through the shaft. I returned both, they shipped me back two and one was leaking and the other had a 38mm top (40mm gate with 38mm actuator cap, no idea how that happens). Eventually after a lot of back and forth I found myself with two non-leaking gates. I believe this happens a lot more then people would like to believe but you would never know if you don't pressure test them prior to installation. Crank Motorsport - Issued a full refund and let me keep the seat rails. I turned them into scrap metal for other projects. GKTech - Shipped me out a replacement and asked that I modify it as per my idea and that they would do the same for a future revision. ATP - Can just needed a large shim to bolt up properly.  Haltech - They started an actual proper Beta channel for firmware's a few months back and stopped using the general public for testing. I'm now much happier.  Speedtek - f**k Speedtek. I would love to watch them burn.     
    • I've got a Turbosmart wastegate, ATP catch can, many GK Tech parts and Haltech everything. Everything's been perfect, sorry to hear your experience wasn't the same
    • The only high-power RB I've personally seen go pop after running for all of an hour on a dyno was built by B2R, while being remotely tuned by B2R. The only wastegates I've ever had leak like a sieve, return, still leak, return and get shipped back the wrong ones were from Turbosmart. The only final drive that I've ever purchased that were unusable, twice... were from Speedtek. The only seat mounts that I've ever purchased that placed the seats in the door frame were from Crank Motorsport. The only poorly designed parts that I had the manufacturer confirm should have been designed as per what I mentioned were from GKTech. The only ECU I've had firmware updates consistently break things are Haltech. The only catch can I've purchased that didn't fit in its advertised spot was from ATP. So forth and so on... Moral of the story, doesn't matter where it's from. Do your research beforehand and stick with products and companies you've trusted in the past.    @joshuaho96 If you want it done right, do it yourself.
    • Something coarse-ish. 180 is good.
    • I was surprised to see all the quick Jack models at the same prices on there. But yeah, grabbing one at 20% off would be great.
×
×
  • Create New...