Jump to content
SAU Community

Recommended Posts

  On 17/04/2013 at 10:41 AM, rob82 said:

Not always - you often will see black smoke during detonation...

If you're getting black smoke from det. would you be able to hear it?

  On 18/04/2013 at 10:14 AM, MrStabby said:

If you're getting black smoke from det. would you be able to hear it?

Sorry to be so vague but generally if you can see puffs of black smoke you could be experiencing fairly heavy knock - so if you've got a good set of ears you may pick it up.

I believe what you are seeing is raw hydrocarbons(un/semi burnt fuel) exiting the chamber - which sounds weird as you've just thermally and physically shocked the chamber which you would think would give you a really good burn however most detonation occurs at the outer edges of the chamber where you may have a localized explosion rather than a progressive flame propagation from the spark plug... This may also be the reason that EGT's drop during det...

Not "normal". Common, yes. But not normal.

If your mixtures are around 12:1 at full load then there shouldn't be a noticable black stain following you around. Things start getting black when you have low 11s down into the 10s. Any factory ECU car running extra boost is a good example.

  On 24/04/2013 at 11:07 AM, JordansR32 said:

Isnt like a little bit of black smoke normal when your at high rpm/put your foot down? Obviously not to much.

I still get black smoke with 18psi and 11.5:1ish AFR's at full load.

Go back and get some dyno sheets (assuming it was done on a dyno) it should be saved and they can bring up high speed air fuel ratio.

Could be a few things bro.

If it is your turbo seals there are a few tell tale signs to look out for.

Check the intake of the turbo compressor for oil. Also when you are coming up to a set of lights rolling to a stop does it smoke a little?

Random smoke at times when sitting stationary at idle?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I might have to say it.
    • Ahh... it's an early RE5R01A box, that means the pinouts I gave are wrong (they were for the RE4R01A 4-speed box)... I'll have to dig around in my docs to see if I've got that schematic (they used the same gearbox plug, with the vacant pin wired to the direct drive clutch solenoid)...prolly hidden away in a supplement somewhere... ...there were 3 variants of the RE5R01A ~ this early schema was what we called the 'dumb' 5 speed ; it's what jatco called a 'medium duty' box, with torque holding up roughly ~200ft/lbs or so, which was good for NA from RB20/25DE and up to around VG30 output spec. With the RB25DET (and VG33/35 mills), the only options they had was the 4-speed 4AX00 box, which had been beefed up to handle the extra torque (primarily for the VG35, but it also suited the RB25DET mill and others)...and the RE4R03 box in large 4WDs a lot of the time... ...the next variant of 5-speed was redesigned, stronger, and 'smart'...first ones had external TCU with internal (on valvebody) Shift Control Unit, pressure switches, and 2 x TSS...and the last ones had internal TCU+SCU setup, with CANbus control etc etc. @DRoc81 On the RHS of the box towards the rear, there should be a stamped silver ID tag -- what's the model number? Oh...and with the early 5-speeds, the torque converter control solenoid assembly should be replaced as well (31940-60X00)...it's a bit Murphy's Law ....if one has failed, bet on the rest not being far behind ...
    • I remembered wrong, but was close though 1Kz setting because those Jaycar SSRs don't go any faster, 1x pump per SSR with flyback diodes & heatsinks. In saying that, the heatsinks are overkill. Just on an alloy plate is more than sufficient. You'll find without a flyback diode, your SSRs will heat up big time and also die prematurely.  I've been running the two same SSRs since the last motor, no issues, car does 2 hour straight drives in summer once in a while and gets punished on the track. Nothing melts, no hot messes, etc.    
    • Hmm. You're probably best off working out what the lobe centreline or even the LSA is for the stock cams, with VCT OFF. That's bound to be out there somewhere. Then, work on the assumption that the Kelford centreline is probably the same, and wouldn't be more than a couple of degrees away, if it is different at all. I'm very surprised that you needed to adjust the exhaust cam by 5° to get it on spec. That screams there's another problem somewhere. Anything from the belt being 1 tooth off (how many degrees is one tooth worth?) to simple user/measurement error on the degree wheel. I say this because Kelford, like most quality cam manufacturers these days, does a pretty good job of actually making the cams to spec, not relying on patching it up afterwards like we had to do back in the 80s.
    • Besides packing it, you can also fill your pump through the oil filter inlet port. After cranking for what felt like an eternity without pressure, i fed a tube in through there and filled it with oil. Cranked for a few seconds after that and had pressure. 
×
×
  • Create New...