Jump to content
SAU Community

Rb25 Vct Oil Feed

megzz

By megzz,
in Engines & Forced Induction

 Share

Recommended Posts

megzz Collaborator

megzz

Posted
Posted

I'm in the process of rebuilding my 25. Just looking at my VCT oil feed, I stuck a pick into it and it only went in a max of 2mm deep. Is this normal, does the oil feed straight up into the gallery from the bottom of the block or does it 45deg into it?

Hopefully this makes sense, I want to make its not blocked because VCT wasn't working when the motor was last running.

post-84181-0-92728400-1367539826_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/424564-rb25-vct-oil-feed/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

Think it works as a check valve so might just be bottoming out the check valve. Just blow some air through and see if you can feel it come out. If the engine is out that is. I think if you blow air into one of the ports where the filter goes and block the other 2 head feeds with your fingers then you should feel some air come out

  • 2 weeks later...
megzz Collaborator

megzz

Posted
  • Author
Posted

So I drilled feed with the top of the block facing down (I used a bit smaller than the hole size so it didn't cut any metal) and some oil dried up like jelly came out. The feed seems free now and I can get a pick in there but compressed air still doesn't come out of the feed.

I've tried blow air through various spots including both oil filter ports and the oil pump port but i get nothing from the front VCT feed!

megzz Collaborator

megzz

Posted
  • Author
Posted

Hi Guys,

Does anyone know where in the oil system does the VCT feed, feed oil from? i.e where does the feed tap into the rest of the system? if possible could you highlight it on a photo for me? Its hard for to now that the engine is partially built.

89CAL Grand Master

89CAL

Posted
Posted

Yeah should be from the same feed as to the other head oil feeds.

oil pump --> Filter ---> main oil gallery ----> Head feeds

From memory anyway, I did sus it out when I had a bare block and some air and some cleaner spraying through it

megzz Collaborator

megzz

Posted
  • Author
Posted

can you track down a pic of the oil feed? if you can get a hold of a manual it will show it

I have the Nissan workshop manual but it doesn't detail the oil flow /path it just shows how to assemble oil pump etc.

Here's a photo of it

post-84181-0-96909000-1369099208_thumb.jpg

I got this from the oil control thread its for an RB26 though

post-84181-0-19310900-1369099313_thumb.jpg

How do you guys troubleshoot a blocked oil gallery - with drilling as a last resort as the block as it has already been cleaned and assembled...

  • 4 years later...
Ben C34 Grand Master

Ben C34

Posted
Posted
14 minutes ago, silencium said:

Sorry for digging up this old thread but I have kind of a similar problem.

Does anyone know if there is a check valve in the VCT oil feed or if it simply is a restrictor?

Thanks for the help

 

Why would there be a check valve?

How would that be useful?

Why do you think there is one?

why does it matter?

 

I vote my ass no check valve

silencium Apprentice

silencium

Posted
Posted (edited)

That is very simple: When the engine is stopped, oil could flow back due to gravity, leaving air in the oil gallery. Next time the car gets started the air has to go out through the journal bearing before the oil follows.

I do not know how much the oil actually flows back, but it is definitely a bit, because otherwise oil pressure would be instant on the first engine cranks during start up. But it usually takes about one second till the oil pressure switch goes off.

Using a check valves in the block would make sense imho.

If one has a RB block laying around it could be checked with a thin wire.

Edited by silencium
typo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Hope the cans went down well at least 
    • Milkmun
      Neil's R33 Gts-t Build

      By Milkmun · Posted

      255 can't go wrong with the price.
    • Kinkstaah
      Neil's R33 Gts-t Build

      By Kinkstaah · Posted

      When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...