Jump to content
SAU Community

Recommended Posts

Ok i installed some GTR camshafts in my RB20 today. also fitted a new timing belt.

so here are my probs.

when i installed the cams i noticed the inlet cam was much harder to turn than the exhaust cam when making small adjustments to align the cam gear marks for no.1 TDC

after thinking maybe the new cam was bent i pulled it and installed the standard cam, but it felt just as stiff to adjust, so back in went the GTR cam.

Now my problem is the car cannot hold idle without droping rpm and then dies

now when i try to start the car it pretty much dies immediately.

is this due to the "lumpy" camshaft or something else?

any advice or help would be much appreciated.

Ben.

Link to comment
https://www.sau.com.au/forums/topic/42478-camshaft-instalation-probs-help/
Share on other sites

  • Replies 88
  • Created
  • Last Reply

Top Posters In This Topic

A bit of a stupid question (I'm not sure how the cam is mounted etc..), but did you put the cam mounts/craddles back in the same position??

I replaced a cam on an old car years ago and it did the same thing, found out that the mounts/craddles that hold the cam in place were put on in the wrong order (my bad !!) which put a fair bit of load on the motor cause they were slightly out of wack.... I ended up needing to get them line bored to fix it...

Not sure if this is your problem, maybe someone else can confirm.

J

I would say, if your belt is on right, marks match up, all hoses back in the right spot (eg. Crank Reciculation Thingi) and CAS on the right mark(by eye), reset the ecu and try starting it and holding the idle up for a couple of mins and see if it help but other than that i'm stumped.

dunno if that is any good tho

yeah i have tried everything everyone has mentioned here.

the only thing i think could be causing it is the fact the inlet cam felt much stiffer to adjust than the exhaust. it was noticably harder to adjust, i think the engine is having trouble turning it over at idle and hence stalling.

the only thing is, when i noticed this problem when fitting the GTR cam i decided to throw the standard item back in position to check there was nothing wrong with the GTR cam. But the standard one felt just as stiff...

i dont think i dropped anything in, i was pretty meticulous doing this job.

there are no strange noises to suggest there is a spanner in the works (literally).

I only can think of a few things that are causing this.

- either the fact the in.cam was difficult to turn is causing the problem.

- the timing belt has jumped a tooth or so on start up (i doubt this)

Considering they are a very mild cam upgrade compared to the standard items the ECU should be able to handle them.

so im stumped here.

i think ill pull the whole lot out and go back the the drawing board.

Hi bbenny, check the clearances (feeler gauges) between the cam lobes and the buckets, if there is a bent valve you should see large clearances that the hydraulics can't take up. If it is not missing, then I doubt this is an issue.

You really need a timing light to confirm the ignition timing. Have you tried advancing the CAS and seeing what effect it has on the idle? We usually have to run a bit more advanced igntion timing at low rpm with aftermarket cams.

hey sydneykid

i invested in a timing lamp today, i did adjust the CAS and it was a little better when advanced but still wouldnt hold idle

it doesnt backfire or sound bad at all, when i drove the car around the block (taking it easy) it was extremely sluggish, i found that response was really poor at low rpm, even if i fully opened the throttle nothing would happen for some time till it reached 3000rpm but even after that point it was very slow.

ylwgtr: i dont think ihave bent any valves because at no time did i rotate any of the cam shafts - i only noticed the stiffness of the in. cam when making a minor adjustment to align the pully marks.

thanks for all the advice here guys, keep it comming, i will begin to pull it all apart again tonight and try see if i have missed anything. if it still doesnt work after rebuild no.2 i will throw the standard cams back in and see if i still have the problem.

sydneykid: did all your installations have good idle or did you have similar problems??

Hi Benny,

I just finished my cam swap as well this past week and the car has been down since with the exact same problem you are describing.

The timing marks are dead on, all 6 plugs are getting spark, and there's PLENTY of fuel, I know this because the plugs almost instantly foul after a couple attempts at idle. I have noticed that when it is colder outside the car will idle until it warms up a bit, my ECU is now pointing the finger at the coolant temp sensor. I have also performed a comp check of all 6 cylinders and they all read the same value, I am under the assumption that if there are bent valves then the comp gauge should not hold pressure (I could be wrong, it's happened before). Of course if I have valves bent in one cylinder then somehow I have valves bent in all six and I think I would've noticed something, a noise perhaps. I have checked everything I can think of at this point and have been using my wife's S14 as a taxi lately. I have ohmed out the harnesses to the AFM, swapped AFM's, CAS's, and ignitors with a friend's known good parts.

But I am so glad someone else has performed this swap and seen the exact same problem as I have. You are not alone...

I'm going to replace my coolant temp sensor tonight after work and see if it makes it better, my car has idled exactly 3 times since the swap and everytime its been after it was a chilly rainy evening.

I'll re-post after I check out this temp sensor issue, hopefully with some positive results.

Of course any other ideas/suggestions are appreciated :rofl:

-Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...