Jump to content
SAU Community

V35 Skyline Navtool - Interface Adapter For Screen

r33skylinegtst
 Share

Recommended Posts

r33skylinegtst Mentor

r33skylinegtst

Posted
Posted

For sale is a V35 Skyline 'Navtool' - this is an interface box that allow you to connect external video sources to the factory dash screen.

Through a shipping error I ended up with two of these, I've installed one in my parents vehicle - as pictured - and the second one is for sale.

It connects behind the back of the factory GPS DVD drive (above the glove box), and gives two video inputs, whilst still retaining the factory info screens if you use them, and will switch to the factory reverse camera (where installed) when the car is put in reverse. These are a plug and play system, so no hacking of wiring looms etc.

It should be noted that the factory screen is NTSC, so to connect say a DVD head deck you'll need the ability to switch video inputs from PAL to NTSC (most JVC's will do this for example). This may also fit the M35 Stagea as they appear to use the same screen, but I can't confirm that for sure.

$200 firm including shipping Australia wide - these normally retail for around $300 by the time you pay postage from the states. PM me if interested.

post-7190-0-81613900-1368622479_thumb.jpg

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Hey guys so turns out this project is going to be much bigger than I thought haha but I've done some my homework and have done a few panels on my car, but one part I can just not visualise is this. If I do a spot repair and I put filler in a dent for example and sand outside of the repair with 320 grit lets say so the primer can stick as I will only put primer on that repair and the surrounding area and then repaint the whole panel. Don't I need to make sure that I don't put primer on the old clear coat? I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down, it's still shiny. I thought putting paint on clearcoat or primer on clearcoat is a bad idea because it won't stick. So in this scenario it's a bit different to mine but imagine someone doing a spot repair and only painting that small section of repair but the new paint is landing on the old clearcoat. What am I missing?
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      I was immediately reminded that your location is QLD. Sounds like a perfect SEQ business idea.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      And if you can't drive bigger injectors with peak and hold as low impedance injectors during low pulse width, it's even harder to get a nice clean known amount of fuel.
    • MBS206
      Upgrade an rb25neo

      By MBS206 · Posted

      From watching the 6 hour, it seems they've really got the class A2 Ford Mustang sorted, as it was cutting it up in lap times with he X1 cars, which are all those late model turbo BMWs. I have no real idea about either of them, but watching what was happening at the 6Hour, it made the Mustang which is meant to be in a slower class look very impressive.
    • MBS206
      NC MX5

      By MBS206 · Posted

      Also Mark, perfect timing for you to offer Fab9 to open an Aus branch for them, where you'll setup all the contracts that basically you're just the paperman, everything goes through Aus for their gear, and you can buy a piece of paper off of them once every 3 months that's really expensive. Tariffs aren't paid on exports after all. And for it, you'll just take 10% cut for your name on the papers. Oh, and a free NC intake setup and air box...
×
×
  • Create New...