Jump to content
SAU Community

S A U - N S W Tech Night For Members 5Th July - Servicing, Blue Slips, Eng Certificates


Recommended Posts

WINTER TECH NIGHT by SAU.NSW
In conjunction with JLM :action-smiley-069:


Many Thanks to Todd O'Donnell for helping SAU set up this big night out!
Thanks too to JLM staff and two Japanese Technicians who are RB & Rotary specialists,
One of whom was head-hunted from Nissan Japan Service Dept.

Day/Date:- Friday 5th July
Time:- 6.30pm till about 9-ish
Place:- JLM 21-23 Bridge St Rydalmere
Parking:- Along western side of the street or on grass verge.
Limited To:- Members Only x30 and Execs x10 = 40 all up
Price:- Free of Charge
Food and Bev:- Supplied by JLM

The Night:-
* 6.30 - Feed tummy
* 7pm - How, When, Where, Why of
a) Scheduled Servicing with 2 Demo Cars on Hoists
b) Tools required and used
c) How to Read an Auction Report
d) Compliancing and Blue Slips
e) Conflict Resolution anecdotes with Fed Gov't
f) Engineering Certificates
g) Conflict Resolution anecdotes with State Gov't

So If You're a Member, Register Now!
If not, then join up!

1) DekA (M)
2) rs88 (M)
3) PN-Mad (M)
4) CLNSKY (M)
5) MrFijiGold (M)
6) twotwisted (M)
7) Owens (M)
8) Victory (M)
9) Clinton (M)
10) Watchamacallit (M)
11) darksky34 (M)
12) RiseofBrutality (M)
13) benm (M)
14) PRO_32 (M)
15) BakemonoRicer (M)
16) ianjb (M)
17) FeZ25 (M)
18) skylinekido (M)
19) NYTSKY (M)
20) sydking (M)
21) MrStabby (M)
22) Philr32 (M)
23) vorse (M)
24) elChin0 (M pending)
25) n11smo (Mpending)
26)
27)
28)
29)
30)
* Prizes given to first few non-Execs whose Qs (that you in written form submit &) are drawn out of a hat on the night. You must be present.


---------------------------------------------------------------------------------------------------------

Execs
1) Bodella (E)
2) Terry_GT-R34 (E)
3) crashdown (E)
4) luke GTR (E)
5) GoldZilla (VP)
6) Daleo (E)
7) 34GeeTeeTee (E) (with Carmen in the shadows)
8) Aggroman (VP)
9) xntrq (E)
10)

----------------------------------------------------------------------------------------------------------

Reserve List Of Members

*** All advice and demonstrations given by workshops, professional practices and factories for SAU.NSW Tech Nights are the responsibility (of accuracy) of the establishments - not the car club.

  • Replies 129
  • Created
  • Last Reply

Top Posters In This Topic

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Ohh even easier.   Go dial up 700rpm on the hand controller. Rip off the TPS plug, wait till the idle drops and then adjust the IACV screw so it's just a tad below the target on the hand controller (say 650rpm), plug the TPS back in and idle will climb back to target. Done.
    • Hey Sleepergm, I love your inlet piping, do u mind sharing who did the work, please? cheers, Ian
    • Yeah, you want the IACV to be running at around 30 "units", variously called "steps" or "duty cycle" depending on the person. That gives it room to go lower if need be and higher ditto.
    • Ah right that makes sense.
    • The RPM is just a target, the ECU will adjust things to try and hit that target but it's by no means guaranteed. If the IACV duty cycle is 0 or something like that and it's actually closing up fully then the idle is as low as it can physically go without reducing ignition timing. The problem can be something like the cold start valve in the IACV not closing fully, worn throttle shaft seals, torn rubber diaphragm in the brake booster allowing unmetered air, etc. 
×
×
  • Create New...