Jump to content
SAU Community

Recommended Posts

Hey all,

I started my car tonight and noticed that there is a clicking sound present from what appears to be coilpack 1 or 2. It was more obvious when the car was cold but then as it warmed up it became less regular.

When I got in the drivers seat I noticed that when the revs are consistent the clicking goes away. When the revs start hunting the clicking sound occurs when the revs reach the lowest point before going up again. Eg consistent ideal is 900rpm, drops to 800, clicks and revs return to 900.

Anyone know what this could be or experienced it before?

Engine: RB25

Computer: PFC

Coils: Splitfire

Cheers,

Konect.

Edited by konect

Coil packs shouldn't click - is it the sound of the spark shorting to the head? Remove the coil cover and observe it in the dark or look on the coil pack for signs that it has been shorting out.

Yeh it does sound similar to the coil shorting which was my first thought. I've done the lights off test and couldn't see anything.

The thing is, it only happens when the revs hunt. If they aren't hunting, then there is no clicking sound. That's what's got me stumped on this one :S

As others have said the clicking sounds like a spark arcing where it shouldn't be. You can pull out spark plugs while the engine hunts to see which spark plug has no effect to the hunting. It could be a damaged coil which the spark is leaking from. Are you sure you're not hearing the injectors pulsing? If the engine hunts, from another cause, the rpm slows down and so does the injector cycle which what you *may* be hearing is your injectors opening and shutting. Again though, seems you've narrowed it down to cylinder 1 and 2 so what I'd do is swap cylinder 1 and 2 coils to 5 and 6 and see if the clicking moves to the back. Inspect the plugs, change if necessary and go from there.

Hmm also read how you said its worse when its cold. Usually if its a coil related issue the problem is more prominent when the engine is warm.

Edited by SargeRX8

Thanks guys.

I swapped coils 1 and 6 today and got a second set of ears on the job too. We 'think' that it might actually be coming from under the inlet near the alternator. The sound still comes from the front end of the motor, but with a second set of ears we thought it was lower down rather than in the channel where the coils are. THe car ran for about 10 mins at 1100rpm without doing it, then as soon as the revs dropped it clicked again. I'm thinking maybe the alternator is being asked to send more voltage to recover the revs and its a switch or something making the sound?? :S

Might see if I can get an auto elec to have a look at it and see if they can pin point where it is. Its hard to pinpoint the location with the inlet in the way and the clutch fan blowing air around.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As long as its NOT a HyperSHITtune, youll be fine.
    • First time visitor and currently getting ready to start work on my HK Premier.  Its all stock, 186 with 3 on the tree.  The only mod i have right now is extractors.  I am hoping to get some guidance on slightly modifying the engine to bring a little more power. Just going for a nice, comfortable cruiser.  The car is very straight, however i have been out of the country for 20 years and its been gathering dust at a family farm.  Will be doing quite a bit of body work to cut out some small rust areas (frnt quarter panels and a few other small bits) and fix up the paint.  Will be redoing the interior (its currently black and the seats are in real need of recovering and respringing the driver side (its front bench seat).  The dash needs a little TLC, but no real damage.  As my heater has degraded I am considering fitting something after-market that will be both heater/AC (recommendations here are always welcome). Wanting something discrete that will allow me to use the same controls and not be obvious once inside the car.   For the engine, i have been told i could consider upgrading my cam (imagine i would need a new head as well) and putting a new carby (currently the original stromberg).  However not sure what is going to be the best route.  Would certainly welcome any comments/suggestions.  As  a final step I am looking at changing the wheels. Current hubcaps are in dire need of refurbishment or replacement (imagine its a bit like hens teeth).  Thinking of some clean/classic looking mags (7-inch should be more than enough - not going for a large change in look).  Welcome any comments/advice and of course any questions. 
    • I got the ARC M079 due to the space constraint.  Been running mint for the last 3 years.  Plazmaman also seems like a really solid choice but not used myself.    Hunt around for a better price but this is what I have - https://www.rhdjapan.com/arc-brazing-intercooler-smic-m079-bnr32.html
    • Wanted to follow up on this. Did you end up getting the M073? Still deciding on what to get between nismo m073-79 and plazaman.  
    • I was just watching these boys up in QLD AWD'ing their S13 too.  
×
×
  • Create New...