Jump to content
SAU Community

Sunroof Into Non Sunroof

Steve.b

By Steve.b,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Trex Grand Master

Trex

Posted
Posted

There are a few ways to do it.

1. Cut the sun roof out of another, trace out the new peice and cut yours and weld

2. Trace out the sunroof and cut, no welding needed

3. Get a pro to do it so its perfect with the roof lining and no creases and leaks.

There are a few how to on youtube on all 3 ways.

I was looking to do it a few years ago, and the only people who wanted to do it were the chop shop, rebel restorations, hollianda etc because everything needs to be perfect.

If the roof is bent the sunroof warped or anything wrong with any of the parts you want to use, it will cost you a lot! Everyone I spoke to said to buy new. I've read a few horror stories about cutting too much out and the other problems mentioned above

RS4StagMan Rising Star

RS4StagMan

Posted
Posted

Best to sell yours if you must have sunroofs and buy a factory one.

A factory RS4 with sunroofs will not cost much more than one without these days, get locally or import from Japan.

The conversion is not that straightforward and will cost $$$$'s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Potential MAP Reference Point

      By GTSBoy · Posted

      Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • MBS206
      NC MX5

      By MBS206 · Posted

      He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • Kinkstaah
      R34 GTT front hood lip

      By Kinkstaah · Posted

      The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • AdiR34
      R34 GTT front hood lip

      By AdiR34 · Posted

      Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
    • Radical_Goodspeed
      Potential MAP Reference Point

      By Radical_Goodspeed · Posted

      So I'm in the final stages of assembling my single turbo RB30/26 and had a question regarding MAP reference points.  I've seen several recommendations such as tapping the cylinder 2/3 ITB, tapping the intake manifold at cylinder 2/3, or using a point on IAC. First two are doable but require permanently modify part and the third is "out" as I plan to delete the IAC.  All that to say my question is can I used the "bleeder" in the center of the ballance tube as a MAP Reference? I'm running a catch can so I don't need it for the PCV system. My thought process is it "pulls" from all 6 cylinder, and it's between the ITB and the cylinders making it ideal for MAP reference according to what I can find. Thoughts?
×
×
  • Create New...