Jump to content
SAU Community

Recommended Posts

genuine nissan HICAS tie rods (different to front tie rods!) are about 250$ for both. from nissan. not cheap. but if you go ling long...well...yeah

well if you got a GT-R I wouldn't use ling long, but I own a R33 GTS-t (ling long is acceptable) haha :)

^ maybe he likes HICAS :)

Theoretically it makes sense to have HICAS, and the system was revised in Series III GT-Rs like yours Paul, prior to that HICAS was pretty shit.

I've tossed mine in the bin too, but I own a fridge.

A lock bar doesn't really solve the problem that you probably have anyway. The outer tie rod ends are the spot that wears the most, and a HICAS delete bar leaves those in place. You'd still need to replace them.

Question.....does 5500 rpm relate to a particular road speed at all? HICAS is known to exhibit it's problems at particular speeds because the HICAS computer reaches "panic mode" at those points when given sensors are not working. Steering angle sensor is one that people often accidentally lose when they put a different steering wheel on the car and the hub doesn't have the drive pin for the steering sensor. On my car (last century) it would crank the steering wheel over to the (left? right?) by about 45° when over 80km/h just because no steering sensor. HICAS panic. No steering sensor also meant I couldn't put it into diagnostic mode which made it very hard to work out what was going wrong. The HICAS computer also looks at VSS, and for all I know in the later GTRs it might even be looking at the G sensors. There's lots of things that can make it act flaky.

Try to put it into diagnostics mode (no, I don't know how to do it on your car, only on an R32). Failing that, get a mechanic with a decent scan tool to hook up to the Consult port and see if there are any codes in the HICAS computer. You may have to take it for a drive and trigger the fault to see anything.

Try to put it into diagnostics mode (no, I don't know how to do it on your car, only on an R32). Failing that, get a mechanic with a decent scan tool to hook up to the Consult port and see if there are any codes in the HICAS computer. You may have to take it for a drive and trigger the fault to see anything.

yeah I'm thinking the same

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...