[Vic] Fs; Various V35 Coupe Parts

[private]

Hey guys,

Over the next couple of months, I will be replacing various parts on my V35. Therefore, the stock counterparts will be up for grabs as listed below.

- Front bumper with aftermarket lip. Some scratches evident.

- Stock side skirts. Some scratches evident

- Non-brembo calipers + rotors + lines

- ?Brembo rotors

Open to offers on all the above

Body parts are painted black

Items located in Melbourne

Patience is requested from future buyers as I will be offloading these items as their after market counterparts arrive in the country.

Other items for sale;

1)

Brand: SSR
Model: MS1
Tyres: 225/35/19f 235/35/19r
Pair / Set: set
PCD: 5x114.3
Diameter / Width / Offset: 19x9.5 +18f 19x10 +24r
Condition: Small gutter rash on the right rear wheel, 1x wheel cap slightly damaged, other small imperfections due to daily use. No hairline cracks.
Location: Melbourne
Willing to Ship: At buyers expense
Price: $3000
Willing to Swap: No, but keen to see what you got. Negative offsets, only 19x10-11 inch wide!

2) JL 13W7 in ported box (not carpetted) and JL 1000/1v2 amplifer for sale!

Can throw in all cabling required. Items are not even 4 months old. Selling it as these were in my old car, and they will not obviously fit in the V35.

$1400 for both plus wiring plus FREE capcitor.

[RR33YY]

Can u post a pic of the aftermarket front lip?

[private]

No worries boss! I'll do it as soon as I get home!

[(Locky)]

Gave up on the camry by the looks

[private]

10 defects later, its time for a change. Haha

[Dreadnought]

That you Numero? Keen to see what you do to the V.

[private]

Hey bro yeah it is haha.

Cheers man. Its pretty stock atm. Them $$$$$ issues though

[private]

Bumpppp

Front non brembo rotors. Plenty of meat left. Have not even been machined once! $140 for both

Non brembo rear rotors. Same as above. $100 for both

Brembo slotted rotors. Little bit of life left in them (Maybe one pad life left depending on which pad you use) $100

Stock non brembo calipers with pads $200

[sonicii]

Might be interested in the non-brembo rear rotors. Any chance you can do me a favour and measure the distance from the outer edge of the rotor to the outer edge of the hub? I found out one of my rear rotors is too small the other day and just want to check what size these are before committing to buying. The one of mine that is too small is 55mm, the other is 60mm.

[private]

Hey mate no worries. Ill also get you a thickness of the disk so you're aware how much meat you have left to play with.

I will do it tomorrow when it's not so cold. Haha

[private]

Just to clarify, essentially you would like the thickness of the hub?

[sonicii]

basically this.

I discovered the other day that one of my rear rotors is smaller than the other and the brake pad is overhanging the edge of the disk.

I didn't have time to remove the whole rotor to confirm the overall diameter, but was able to measure the figure shown in the pic, the small rotor had a measurement of 55mm, the rotor on the other side which looked correct was 60mm.

[private]

Ah touche. SHall do it after work for you boss.

[GeeDog]

I've got the original rear rotors of my coupe in the shed, and just measured them at 55mm (actually closer to 54mm). Both have a small un-worn (is that even a word) strip around the outer rim, so the pads definitely weren't overhanging the rotor. Just to clarify, I have a 2003 premium coupe, and these were the standard (non-brembo) brakes. Were there different calipers on different years?

[sonicii]

I'm not sure, but I guess they must be, mine is an 05 350GT sedan, the rotor on the left side is quite close to 60mm and the is only a small strip around the edge that is unworn, like yours. But the pads on the right rotor overhang by about 3-4mm, which suggests the right rotor has been replaced with one for a different year/spec, but I can't find anything to suggest there are any differences, other than the brembos.

The Callipers and the pads on both sides look identical, so I am assuming it is just this rotor that is wrong and not everything except this rotor??

Thanks for checking though!

[GeeDog]

If it helps - my rotors are 292mm diameter & 16mm thick. The calipers have "15" & "4306" cast next to the bleed nipple, and "27A" cast above where the pads sit. I've got a full set of F&R rotors & calipers in the shed, so if you want any measurements or pics let me know.

[sonicii]

Thanks for your help.. I actually created a new thread about this issue on the weekend.. I might post some further info in there if you are interested, instead of clogging up this 'for sale' thread.

Edited June 25, 2013 by sonicii

[AsM]

Series 2 v35 got bigger brakes in general than series 1 and the brembo became an option even for 6 speed manuals (or not available at all, havent seen a series 2 or 3 with factory fitted brembos so far)

[sonicii]

Yes, I think the brembs were only available on the s1. Didn't know the standard brakes were

Different on the s2/3. It does answer a lot of questions thought!

[coupestar]

hi can you post some pictures of your bumper for sale