Jump to content
SAU Community

Recommended Posts

There is no water seal in the turbo, the water runs around the core, so there's no way a turbo could leak water internally.

crack/fracture in the core?

definitely NOT saying this is the problem, but merely a possibility.

I'd be checking the PCV valve and associated breathers are functioning as intended. It looks like your getting excessive pressure in the crank case. If the PCV valve isn't closing under boost you'll get huge amounts of oil in the intake etc, just like your pic

UPDATE:

Compression test showed:

130,130,130,130,75,75

Diagnosis is broken head gasket between cylinders 5&6 causing a leak between cylinders. I bought a new motor with 83,000 kms straight from Japan. Taking delivery on Monday. I didn't want to risk opening up the motor to find broken ring landings as well; clearly this motor has had a hard life and its cheap enough to throw away.

ALSO:

I sent one of my turbo's off to Hypergear for the $880 High Flow treatment (much cheaper than at precision turbo's).

NEXT QUESTION:

At hypergear they are trying to sell me braided oil lines for the turbo for $88. Is this even necessary? I'm a bit skeptical.

I'm still driving the car just low boost and it drives okay, only problem is the BoV is messy (spits water+oil) and it blows some smoke. New engine + turbo should be in by 10-14 days roughly.

Let me know what you think about the braided oil lines.

Turns out the turbo's were fine all the time but i still want the hiflow

Edited by Blackkers

The new highflow uses a different core to your old turbo, so to make the easiest fitment happen, just buy the flexibles and be happy. Better than trying to fit it up the old hardlines, seeing as they won't quite line up (probably) and you'll end up cursing and swearing and bending stuff and all that.

The new highflow uses a different core to your old turbo, so to make the easiest fitment happen, just buy the flexibles and be happy. Better than trying to fit it up the old hardlines, seeing as they won't quite line up (probably) and you'll end up cursing and swearing and bending stuff and all that.

Okay thanks for that I will buy the new feed line. I remember trying to fit the original lines to the new turbo when swapping with a stocker; it was hell. I kept dropping the f**king washer off of the banjo bolts from the water feed haha I'm sure I'm not the only one who experienced that.

Next Question (thanks for being so helpful):

I have a stock turbo for sale, with a receipt from skyline spares. How much do they normally go for?

Also, will someone buy my old block? It ONLY suits a rebuild. But someone might want it to build instead of taking their car off the road for weeks to build theirs.

edit:

I'd postpone the highflow until you're completely confident you've addressed the current issue. Remember even if the compression test comes back ok, you still have a problem to fix.

Also, dont forget you may need injectors/AFM/programmable ECU and tune = $$$$

I forgot to mention I already have FMIC, 3 inch turbo back exhaust, Splitfire coilpacks, Excedy HD clutch

I will need an ecu + injectors + tune + possibly fuel pump & FPR to make more power. I had the plugs gapped to 0.8 when they were out for the comp test this morning and I'll get my workshop to check how much meat is left on the clutch when they swap it to the new motor.

Will I be able to run low boost with the hi-flow turbo on the stock ecu + injectors + FP + FPR? people have said no but not even 8 psi until I save up for a tune?

Edited by Blackkers

Search up toshi his in Sydney aswell and can chip the skyline ecu and road or dyno tune for half the price of a nistune

You will need a new solid intake as the std rubber ones suck shut with more boost and a new fuel pump and z32afm

You might get away with the std injectors best to ask toshi as his tuned plenty of skylines and is good at what he does

You will need a braided oil line as the factory hardline apparently has a restrictor in it so it won't flow enough oil for the Hypergear turbo. You can make your own braided line for pretty cheap if you want to isn't very hard

okay good info thanks guys. Where can I get a solid intake pipe for airbox --> turbo inlet?

The smallest actuator available is 15psi. Can I run that on the stock ecu? I have a feeling people will say something along the lines of 'no you can't you'll blow the motor'

I'm going to call the dude tomorrow to talk about a few more things but I'm interested to hear other people's experiences.

I'm also going to contact toshi I've heard great things about him

Thanks again for the input

Edited by Blackkers

Various people will make you a metal turbo intake pipe. ScottyNM35 as an example. Or pretty much any workshop that does mod work like custom intercooler piping etc.

And no. a 15 psi actuator is going to be bad mojo. You need a stock RB25 actuator to keep it safe.

I'm on the north shore of Sydney. Wet test showed little improvement. I'll get the timing belt and water pump swapped over before the new motor goes in.

Anyone know a good timing kit and water pump to get?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
    • Excuse me, but 2) does apply 1) Would also apply if you consider how much is spent in the alternatives. Also there's the option of 3), buy one pre-built that you can put your family in (it's me, it's my car)   That said, I went on a ~500km drive the other day. I didn't use anything more adventurous than 3rd/4th gear at about ~3000RPM and 50% throttle and I was going as fast as anyone has any sense doing on a public road, with enough grip to the point where I didn't want to go any faster. I was obviously under the limit of the current car etc etc. MX5 with 2.5 N/A to achieve the same speed would be more fun for any road scenario. Maybe consider cams. I wouldn't boost it. The use case is just not there and it won't actually make the car more enjoyable unless you really do plan on wringing gears from 1st to 3rd (at least) at 100% WOT on a public road to 150+kmh.
    • Great if: 1. You had all of the money for everything else that is required  2. Lived in a country where you could actually do this and drive it legally on the road Sadly, neither applies to me As for the turbo, I am having second thoughts, mainly for engineering/registration legality reasons and insurance  Not saying I've finished doing stupid things that I probably should do to the MX5, but boost, and V8 engine swaps isn't on the cards Strange, but true 
×
×
  • Create New...