Jump to content
SAU Community

Recommended Posts

Hi guys,

I am new to these forums as I have just purchased an imported R33 GTS-T RB25DET 2door.

Car is immaculate and everything is great apart from 5th gear randomly popping out / trying to pop out.

Every other gear is perfect though.

I have been told that the little nylon shifter bush can cause this? is this true? or am I being told rubbish?

I have driven the car for 7 hours (when I drove it back home after purchase) and it drove great apart from the 5th gear issue.

I have tried to see if it is a load related thing, acceleration or deceleration..... but nothing seems to be a common thing causing it to randomly pop out / try to pop out / gearstick wobble when in 5th gear.

It doesn't happen the whole time I am in 5th gear, only after a few minutes each time.

Any ideas?

Change out shifter bush maybe? change out oil to redline shockproof? anything else to try before I get a local gearbox shop to strip it down?

Thanks,

Dan

Link to comment
https://www.sau.com.au/forums/topic/427923-r33-gtst-gearbox-jumping-out-of-5th/
Share on other sites

There is a 2 part rubber bush to stop things getting in the car and noise as well. The lower one gets pretty close to the stick and mine was making my car pop out of gear.

There is another rubber boot that hugs the gearstick and goes over the gearbox.

Just take the 2 other rubber boots off and see if the problem goes away

Otherwise I wouldnt think the nylon bush would cause it to pop out of gear unless it was heavily worn. Might be a problem with the gear detents if it turns out to be a gearbox issue

I haven't had a chance to check out the boot/s around the shifter yet, but I did start the car up today (as it is not registered yet as I am about to move house, etc) and when I jumped in it I could smell gearbox oil.

I assume this is a good indication that the boot/s are fitted incorrectly, or not seated properly, etc.

When I investigate more, I will report back here.

Thank you for all your help guys.

Cheers,

Dan

Edited by RT40Corona4AGTE

More then likely the rubber boot that goes around the lower half of your shifter then over the gearbox is cracked. This happens alot. When something is wrong with the other 2 boots you will smell oil in the car.

5th synchro hub sounds worn to me. They usually pop out under deceleration going down a hill, but can do sporadic things as well. A busted selector or something in the selection process can mean 5th not engaging completely too...but usually you experience issues in other gears too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
    • From there, it was just a quick electrical check, prime the oil and start her up Which, is not what happened. 1. Bloody seppo Aeropro battery holder. Not only was it too tall for the battery (which I'll forgive them for, I have another battery the same nominal size that is taller than Neil's one, but the bracket is a fixed height so the battery was spaced up) But the thing that really shits me is the hardware to hold it on requires a 7/32 Hex key. WTF. No-one will ever be able to remove or install the damn thing without a hex key they don't own 2. Kill switch no longer worked once the console was installed. Neil mentioned above he had to adjust the length but it no longer cleared the console once installed. Sorted. 3. Suspiciously, the brake light holders were hanging in the boot with no globes. Sure enough the stopper on the brake pedal was missing so they are always on unless the kill switch is activated. Will pick one up tomorrow (turns out 32 and 33 don't use the same stopper) 4. All that sorted, I turned on the kill switch, turned the key to ACC. Nothing. Turned it to IGN. Nothing. Checked some fuses and found the main IGN in the boot was missing which improved things once it was replaced. Now ECU and dash lights turn on with IGN but still no fuel pump. 5. Turned it to Start....ECU on, no fuel pump, no starter. Plus the voltage dropped straight to 9v.  I suspect the starter is f**ked but am going to have to work through it all and see what is happening, really looks like more than one issue. Does anyone have the R33 fuse box key with the circuit it sources from (eg BAT, ACC, IGN, SRT etc) and supplies? I can find a translated list showing Amps and circuit without supply circuit, and I can find supply circuit without Amps and target circuit.
    • 3rd time lucky, the AAC is now all plumbed up after getting some final fittings All set up under the plenum of maximum access
    • OK, so the weight has been bugging because it was really low. I did it again today and got a more believable answer at 1246 without driver And with a 93kg driver I'm pretty sure the car was still slightly on the quickjack last time meaning the full weight was not on the scales  
×
×
  • Create New...