Jump to content
SAU Community

Recommended Posts

is it my rings?

1'2'3'4'5 are 175, throttle flat

number 6 is 110?

put 5ml of oil in number 6 went from 110psi to 130

put 5ml in number 5, went from 175psi to 205psi

are their any other tests i can do?

low kilometre standard engine

Could be rings, but you'd expect a much bigger improvement on #6 than on one of the good cylinders on the wet test. So on that basis you'd expect a BHG or bad valve or something else (like all the bad options like a cracked piston, cracked head, etc etc). Valve most likely.

warm the car up, and test it again.

i once had a cyl read 80 when the rest were 130, then i tested it again 2 weeks later and that cyl was back to normal again. have no Fn idea why.

tested it after i purchased new engine internals btw. guess they were not needed... at least for a few months after when something else let go

DISCLAIMER: I may be wrong (If I am please someone correct me, I love learning about this shit)

Your wet test results showed a bigger improvement on a normal cylinder (weird right?). This suggests that your cylinder bore in #6 is likely okay; it points towards head gasket problems or something in the head.

I'm no guru but I'd be checking for symptoms of head gasket problems first as they stick out like a sore thumb.

edit: also I just wanted to mention that those comp. numbers sound a bit high. Anyone else think the same?

Edited by Blackkers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wow that's a steal, you've done well there. 
    • Exterior LEDs R34 2Dr R34 4Dr Position Lamp T10 T10 Winker front T20S T20S side T10 T10 rear T20S S25S150 Anti-hyfla relay TYPE3 TYPE3 tail T10 T20W Stop Lamps T20W T20W High Mount T16 T16 back T16 T20S number T10 T10 trunk T10 T10 Interior LED Item No.     Map Lamp BA9S single-sided     Room Lamps T10×31     Trunk Lamp T10     meter Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     Liquid crystal section T6.5 pedestal     Winker T6.5 pedestal     High Beam T6.5 pedestal     3 SERIES METER Early T6.5 pedestal     final T6.5 pedestal     NISMO T6.5 pedestal     air conditioner Early Liquid Crystal T3     Late LCD T4.2 Short     button T4.2 Middle     Hazard SW T3 Pedestal Short     Keyring T5     Cigar Socket T5
    • Howdy all,   I had my rb25det S2 rebuilt and finally started it today but have run into a few issues  Engine sounds like a a diesel easiest way to summarise like small ticking, gets louder when revs are slightly adjusted  The engine builder repainted the engine cover leaving no where for me to go off with lining up the CAS so have it as central as possible so not sure it that could be affecting it?, changed the gearbox fluid too but won’t seem to go into gear when running, and only 1 to 4 when off having a hard time finding 5th and reverse anyone got any ideas or a base for me to start off? much appreciated 
    • Well, no. It's an 023, which is pretty similar to an 040. Although it is hard to tell from the specs, as given.
    • Hmm. Maybe the (other thing I forgot about!) Haltech removes at least some, if not all, of the problem I described. I guess there is still the possibility of getting it wrong if the AC is set up/wired up for the Haltech as if it was in an R34 (simply because it's on a Neo), and that's playing foul with the R32 AC computer.
×
×
  • Create New...