Jump to content
SAU Community

Recommended Posts

motor:

S1 RB25

Z32

bigger inj

power fc

splitfires

ect ect

car runs, idles drives perfect until about 5000rpm in any gear, same spot in the rev range each time it will just start running on one or two less cylinders, clutch in and free rev and it goes away and runs perfect again

the Power FC is brand new, was still doing it with the Nisstune the car came with

the Splitfires and spark plugs are brand new

car was put on the dyno and tuner suspected there was a missing earth somewhere in the loom, but has been checked over and theyre all there so im a bit stumped

any help would be appreciated

one thing I havent tested which i will tnight is if it still does it when cruising and getting the revs up on half throttle for examle

Link to comment
https://www.sau.com.au/forums/topic/428267-s1-rb25-weird-problem/
Share on other sites

new symptoms

was running rough while driving, gave it a free rev and at 5k (wouldnt go past 5k) coughed and spluttered and then shut up, clutched out to start again and wouldnt start, pulled over, turned key and started was spinning but motor not cranking, left for 2mins, started up fine and ran fine again???????????????

Have you got laptop or commander for it?

yup have the hand controller in the glove box

Spark plugs (cracked) caused revving problem and wrong injector seals caused similar symptoms for me. Took ages to diagnose and lots of swearing.

will check plugs, someone also suggested a vac leak, maybe good idea to put smoke machine through it? can rule out vac leak and injector seals at same time

Pressure testing the intake would be a good idea, and check the vac lines to the fuel reg/map sensor if you are running one.

shall try get the smoke machine on it on the weekend and yeh has Turbosmart FPR

Well, in that case, there's a sensor check function on the commander. Just find it and use it.

will do tonight, thanks for that

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Throwing my spoon to the soup here a bit.  When I installed a 044 back in 2012, along with the direct power mod, the car became very difficult to start. To a point I burned one starter motor as I was late for work and tried to get the thing going. With some tuning and careful use of gas pedal when cranking it became bearable. Trying to make this short as possible, but the 044 died after 2-3 years, after which I went with an AEM 320lph pump, which also died after about 4 years to my dismay. After that I went with a Nismo pump, and while trying diagnose an emissions problem, I noticed for the first time that my fuel pressure was 5bar/72psi on idle, and that removing the vacuum line did nothing. After monitoring the situation, and removing the direct power feed and going back to FPCM in attempts to remedy it, I noticed there was fuel in the pressure regulator vac line. Kept the FPCM, installed AEM external regu and the car became sooo much better in every way, including starting. And I had driven it like it was for 11 years.. Anyway, I agree these are likely two different problems, and the FP problem you just haven't noticed before. I do not know much about haltecs, but what first came to mind was the CAS, which probably is not there any more. So how is the wiring from haltec to gauge cluster? How is the battery voltage and alternator?
    • Your car was auto before? You have different diff ratio (auto vs manual i think? or n/a and turbo?)
    • +1 for getting a screen off alibaba, CarPlay/Android Auto is vastly better than whatever navigation cars had 10 years ago. I got an Android screen for my 2015 BMW, huge difference. Fully compatible with factory stuff including iDrive controls.
    • Yeah, my offer was more to show exactly how rough and ready the rig can be and still be useful. Youtube vids will definitely show cleaner setups. Same concept though.
    • I would guess the seal has gone down at the speedo drive and gearbox oil has crept up the drive cable sheath and fouled the speedo head.
×
×
  • Create New...