Jump to content
SAU Community

Oil In Radiator

Adz2332

By Adz2332,
in Engines & Forced Induction

 Share

Recommended Posts

Adz2332 Grand Master

Adz2332

Posted
  • Author
Posted

have just serviced it.

so will keep an eye out.

How quick is to quick to see some back in there? bearing in mind its only the smallest amount. its like just a bit of scum up the top when i serviced it after a bit over 5000kms>?

GTRNUR Grand Master

GTRNUR

Posted
Posted

This is a very common issue with metal head gaskets when they have been installed dry (no hylomar spray), or if the head and block weren't surfaced exactly dead flat.

Provided your not leaking combustion gasses this is easy to fix.

Get yourself a cheap ass ebay radiator or an old second hand one. Fill the coolant system with water, bleed the air and go for a drive to get it up to temp.

Shut it down, and VERY CAREFULLY with a very big towel or rag, take the radiator cap off. Give the top radiator hose a few squeezes to get rid of some of the water.

Start the car and then empty a bottle of BAR'S Stop Leak (Cooling system sealer) into the radiator. (Lots of auto shops stock this stuff) Top up with water and put on your cap.

Drive the car like this for about 2-4 weeks. Then drain the water, flush the system through a couple more times with water (running it up to temp each time).

Last of all, swap back in your good radiator and fill with coolant.

As a precaution, it would be worthwhile having all your head studs torque settings checked too. This is a cam covers off only job, and is perhaps an hours work at most for a good mechanic. This is an overkill check though, as if something was loose you'd have nothing but combustion gas in your radiator. Not just a little oil.

Adz2332 Grand Master

Adz2332

Posted
  • Author
Posted

Ah thats makes a bit of sense actually.

I ran my tuner, who also did the engine rebuild and he said he would be shocked if it had done the gasket or cracked a head etc.

He to said along the lines of when the gasket was installed there may have been something wrong etc. and they will check it out no charge for me and go from there

  • 2 weeks later...
Adz2332 Grand Master

Adz2332

Posted
  • Author
Posted

Just an update.

Just got the car back yesturday.

All checked out fine.

Head was tested along with the head gasket both fine.

Had a compression test, come out excellent.

The cooler was leaking slightly but leaking oil OUT not in, but that has been fixed.

The little scum / oily film has been mainly put down to it being a new motor and during the rebuild may have got some in there along the lines.

So all in all, its all good. Flushed the radiator etc out for me to and topped up with coolent no charge, long story short im a happy man!

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

Just an update.

Just got the car back yesturday.

All checked out fine.

Head was tested along with the head gasket both fine.

Had a compression test, come out excellent.

The cooler was leaking slightly but leaking oil OUT not in, but that has been fixed.

The little scum / oily film has been mainly put down to it being a new motor and during the rebuild may have got some in there along the lines.

So all in all, its all good. Flushed the radiator etc out for me to and topped up with coolent no charge, long story short im a happy man!

good thing the hg wasnt changed for no good reason eh?

glad its worked out cheaply for you too

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Cleaning my wheels 😍

      By GTSBoy · Posted

      Yeah, my moulds and seals are 32 years old now. I think I will continue to not use a pressure washer on it.
    • Shoota_77
      Cleaning my wheels 😍

      By Shoota_77 · Posted

      I hear the old "I'd never use a pressure washer on my motorbike" BS in the dirtbike community too.  The only people that have had a problem from using a pressure washer on anything are the people that aren't using them properly.  If you hold the wand any more than 45 cms away from pretty much anything (radiators, wiring connectors, paint, etc) you aren't going to cause any damage.  We've had detailers wreck moulds and seals on cars at work before and the only reason why is they held the pressure washer too close and on the one spot for too long.  If you have 5% more brain power than a detailer then you know not to not do that and you'll never have a problem.
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      I'm pretty much healed up post surgery so I spent another almost full day out in the shed re-arranging everything to make room for all of the shit that I've taken off the car.  I need to get everything off the floor and away from the car for when I start making a massive mess stripping off the remaining body deadener and then for the the painting process.  Almost got the shed to a point now where I feel I can actually start working on the car again (clean shed clean mind or something!).  Almost 11 years of accumulated car parts, building supplies, tools, junk, etc have taken a long time to get in some sort of order again!  Most stuff is now boxed up and in the back shed if it's not car related.  Most people would still be horrified walking into my shed but it's significantly better than it was before!   For those that saw my separate post the other day, yeah I ordered one.... This version- I convinced myself to stop being a clown, wake up to yourself and realise it will take you 5 weeks to make one by which stage you're over working on the car again...  Maybe I am getting on top of my "mental ailments" and making smarter choices.... $1450 delivered which will take my miserable half-dutch arse a few days to get over having spent that much!  If I don't have a use for it straight away after my car is off it I might even see if there is a "rental market" for them.  See if anyone wants to hire it for a period of time.  $25 a week or something like that.  I'll worry about that when my car is actually ready to come off it though as that might be a while away!! There's now no excuses now for not ending up with an underside you could eat off! Away for kids sport the next few weekends so hopefully can get the rotisserie assembled ready to go for the car to go straight on it the next available weekend.    
    • The Bogan
      Cleaning my wheels 😍

      By The Bogan · Posted

      I always use my Karcher, but it's only a little one that I picked up from Supercheap  The only issue I ever had with a pressure washer was when I was a kid cleaning coaches, they had a hi-po industrial sized petrol jobbie that would strip paint if you got to close I saying this, we have a fairly high power washer at work with a diesel powered heater that sprays water at about 60°c, it works great for removing old wax and road grime on the underbody after some foam cannon action, albeit from a "stand off" distance of a few feet
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Sorry no - The sandtrap adventure ended the day, happened at the end of the last session. At that time I wasn't hearing any weird noises nor were the brakes shuddering anymore. It was only when watching the videos that I remembered I had these sounds early on!
×
×
  • Create New...