Jump to content
SAU Community

R33 RB25Det for Sale, $1750

skylineakt
 Share

Recommended Posts

skylineakt Rising Star

skylineakt

Posted
Posted

Hi Guys,

I got a RB25DET for sale.

I came from my half cut which I mainly used for panels and some parts.

The engine is 90% complete.

The items that are missing include:

air-con compressor, crank sensor, front cover, balancer and power steering pump.

For this reason I'm selling the engine off pretty cheap, $1750.

There is an auto box as well if anyone is interested.

Melbourne base, as pick up is prefered.

Link to comment
https://www.sau.com.au/forums/topic/42846-r33-rb25det-for-sale-1750/
Share on other sites
Keishimas96 Apprentice

Keishimas96

Posted
Posted

hey jsut wonderin.............thru your pics it looks like ts missin the turbo and all associated components or is that jsut elsewhere.........

if so did u eva run the engine.............how many km's..............wat year

if it is in good nick i am very interested.

thanx

Keishi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Everything I found online said never use it because it'll dramatically reduce belt lifespan.  No, but I have seen excessive v-belt tension cause the audible bearing noise from excessive radial load in things like alternators. So don't overdo it. Ideally you set it to manufacturer spec using a proper belt tension guage. I tried the "clicker" type gauges but those cheap things are trash. They read way too low even when you're careful.
    • joshuaho96
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By joshuaho96 · Posted

      This is kind of where I've ended up for the most part. It's easier for me, easier for shops that don't have to deal with my weird criteria/picky standards, etc.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      Will do. Suprised if it's not the starter motor considering it's 30 years old. Will get a volt meter though. Battery is close to new.   Cheers for your help, always appreciated.
    • GTSBoy
      Rb25det Belts Change

      By GTSBoy · Posted

      This almost never happens these days. No. Clean your battery terminals and make sure they are tight. Use sandpaper on a dowel if you have to, to get oxidation off the inside of the terminals, particularly on the -ve. Check the earth cable from battery post to chassis ground and engine ground. Make sure the contact surfaces are clean - including the threads on the bolts that anchor them - because that's where a lot of the contact occurs. Wire wheel on a drill is a good thing for this. Make sure the crimps on those cables are all sound. Assuming none of that causes an improvement: Check the battery voltage after it has been resting for a while. If it's at the lower end of the range, put it on charge for a while, then see if it will crank better.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I just checked my belt, it wasn't super loose but I could bend it past 90 degrees a small amount so I tightened it up and for the first time ever my car didn't crank first time, had to crank it again lol. Don't know if that was because I tightened the belt or if it's my starter motor going out (been having slow starts for some time). Coulda also been when I was recording I didn't crank the key properly and it didn't save the recording lol.   Is that a thing if you overtighten a belt it struggles to start?
×
×
  • Create New...