Jump to content
SAU Community

Recommended Posts

These are most the parts for sale Ill just add as I go :yes: Remade thread as old one was getting to big.

Under dash panel driver side with fuse box cover $20

Stock r32 side mount intercooler $50

A pillar trims $30 each or $50 for a pair

GTST air con condenser $70

2 x r32 hand brake and cable $70 each

GTR front strut brace $100

2 x pairs of r32 5 stud front hubs and up rights $100 a pair

Under dash panel with fuse box cover $20

4x lower quarter trims $30 each

Rubber gear box surround with metal ring $20

2xglove boxes

Under dash trim panel $15

R32 glove box $30

3 x speedo clusters 2 x grey, 1 x blue dials $80 each

3 x climate control unit $70 each

centre console dash panel radio surround $40

Upper rear trim driver side all clips still there cracked in corner otherwise good con $40

Rear bar $70

Rear reo $80

Tail lights $70

Steering Colum surround $50

Rear parcel shelf $50

Centre console ash tray $10

Window black box driver $50

Front bonnet latch and support $50

2xwiper motors $40 each

RB20 speedo cable $80

Nissan din pocket $20

Washer bottles rad overflow and washer $50 each

Non projector headlights $200

1 x passenger window switch $50

Air con box $50

Heater box $50

Passenger window reg $80

Passenger and driver kick panel $20 each

Boost sender/sensor R32 $20

Clutch pedal $80

Break pedal $40

Carbon canister $20

Boot lid $80

Bonnet latch and cable $40

Fuel/boot cable $50

2 x stock r32 steering wheels good condition one $70 little ratty $50

Surround ash tray $10

Mirrors $60 each

Front LCAs $120 a pair

Fuel pump $40

Dash all good vents $200

Door shells $100

2xcluster surrounds $20 with some cuts in them

Light switches/wiper switches $30 each

Carpet $100

Gear boot $10

Hand brake boot $10

Driver side dash vent $40

Sun visors $10 each

Rear view mirrors $20 each

Clutch master $30

Gear boot plastic surround $30

Indicators with wiring no outer covers $10

Wiper arms $10

Driver dash vent $40

Stereo brackets $20

R32 Mspec plastic bar $200

2x driver side window switches $70 each

Fuel tank $150-

gold coast and kilcoy

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m only posting this cause I thought I had seen a bad review on these somewhere before. Any feedback? Would you guys recommend that if I do buy these I send em to RC to have em checked before installing. Or any other suggestions?   https://www.ebay.com/itm/114009965865?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JDl-15yLQ8C&sssrc=4429486&ssuid=QTzlFXB1S-S&var=&widget_ver=artemis&media=COPY
    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
×
×
  • Create New...