Jump to content
SAU Community

Recommended Posts

Just got back from Wakefield. R888 can choke on a big dick. Mine were old, so they took a while to get some heat in and come back to life, but I got juddering understeer, the got hot, and then wouldn't turn. I had nt01 on the rear which was better, as newer, but found they went off after 5 or 6 laps. May need to decrease pressure more.

End of the day, the semis were no faster than my federal RSR time.

Interesting!!

Might add, I can't drive for shit, and I pussehed out under brakes lots.

Also, semis are a lot more communicative v rsr, and I found myself catching oversteer better.

Well i will be in the same situation! Will try do a run on RSR too see how i handle that first ;)

Is anyone out there running the same comp tyre for sprints and hill climbs and if so are you just starting the pressures higher for hill climbs???

Yep. I used to run A032R and Toyo RA1 back when I was hillclimbing and sprinting. For hillclimbs you basically want to start with cold pressures set to what the tyre's hot pressure should be at sprints - depending on how much of a burnout you do, you might start the rears a pound or two lower.

Just got back from Wakefield. R888 can choke on a big dick. Mine were old, so they took a while to get some heat in and come back to life, but I got juddering understeer, the got hot, and then wouldn't turn. I had nt01 on the rear which was better, as newer, but found they went off after 5 or 6 laps. May need to decrease pressure more.

End of the day, the semis were no faster than my federal RSR time.

old semis on the front and newer ones on the back was never going to be a recipe for success. Particularly in winter at Goulburn. Not really fair to compare them to a matched set of RSRs all round.

I was pretty critical of R888s when i had them, because they didn't seem to offer much grip. But they can produce good lap times if you are prepared to throw the car around. I was only a tenth faster at Lakeside when i changed to FZ201s. But the car felt much more planted on the Federals, and needed less steering angle almost everywhere.

People say the R888 seem to work well on light cars. I think its more that the really light cars tend to be less powerful. R888s don't like putting power down while exiting corners in my experience. A lighter less powerful car wouldn't really test them so much in that regard.

Edited by hrd-hr30

old semis on the front and newer ones on the back was never going to be a recipe for success. Particularly in winter at Goulburn. Not really fair to compare them to a matched set of RSRs all round

Yup, agree with you, when I cleaned them up this morning for storage, I also found the front left, the one I was having trouble with is 6 years old. Lol.

I'll try some re55s on the front next track day.

Wakefield wasn't actually cold yesterday, it was quite warm.

Yep. I used to run A032R and Toyo RA1 back when I was hillclimbing and sprinting. For hillclimbs you basically want to start with cold pressures set to what the tyre's hot pressure should be at sprints - depending on how much of a burnout you do, you might start the rears a pound or two lower.

.

cool, thought that might be the case. Still bummed about the federals, have searched around and found a few other sites where people have found a difference in the new FZ 201's. at 365 per corner they would of been very affordable. That's life I guess. Kumho's still the hot favourite I think ATM, performance-dollar-life wise. Not much cheaper than z221's but life span is sounding better still.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...